Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*bellhousing\s+needed\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*bellhousing\s+needed\s*$/: 8 ]

Total 8 documents matching your query.

1. bellhousing needed (score: 1): Author: "Bellis" <Bellis@isoc.net>; Date: Wed, 20 Oct 1999 19:29:35 -0400; tiger buddies: i am in need of a bellhousing (6bolt)for my mk 1 tiger that my heh-e trans will bolt to, i also need a set of exhaust manifolds thanks to all bob "b9473215" ellis; /html/tigers/1999-10/msg00294.html (6,221 bytes)
2. bellhousing needed (score: 1): Author: KJENSSEN <KJENSSEN@aol.com>; Date: Sun, 26 Apr 1998 13:24:38 EDT; I am in the process of restoring my 65 Tiger. I have decided to place my original 260 v-8 on a stand and store it away. I have acquired a 1987 302 v-8 and am in the process of completing a rebuild o; /html/tigers/1998-04/msg00221.html (7,419 bytes)
3. Re: bellhousing needed (score: 1): Author: MWood24020 <MWood24020@aol.com>; Date: Sun, 26 Apr 1998 14:47:47 EDT; I did the same swap, using a RHO 302, and found that: 1. finding an aluminum, six bolt, narrow pattern bellhousing was worse than a "needle in a haystack" 2. the dual pattern bellhousings were cast; /html/tigers/1998-04/msg00222.html (7,417 bytes)
4. Re: bellhousing needed (score: 1): Author: MWood24020 <MWood24020@aol.com>; Date: Tue, 28 Apr 1998 23:22:16 EDT; There are a number of sources for an appropriate slave cylinder bracket, including Sunbeam Specialties. However, most are just an aluminum plate cut in the correct pattern. If you have anything besi; /html/tigers/1998-04/msg00251.html (7,309 bytes)
5. Re: bellhousing needed (score: 1): Author: "Doug Mallory" <rdmallory@earthling.net>; Date: Wed, 29 Apr 1998 06:18:19 -0400; I would recommend the slave cylinder collar that goes inside the PAW has them for about $250. Doug in plate, ribs; /html/tigers/1998-04/msg00261.html (7,919 bytes)
6. Re: bellhousing needed (score: 1): Author: Steve Laifman <laifman@flash.net>; Date: Wed, 29 Apr 1998 07:56:45 +0100; Doug, et al I looked into that hydraulic throw-out bearing slave replacement and have the following observations: 1) It's damned expensive. 2) If it needs fixing, it's "take it all apart" time, and w; /html/tigers/1998-04/msg00263.html (7,943 bytes)
7. Re: bellhousing needed (score: 1): Author: "Doug Mallory" <rdmallory@earthling.net>; Date: Wed, 29 Apr 1998 11:30:13 -0400; the Yes wether Yes I have been running one for 2 years with out a problem. If you don't make sure the master cylinder has the correct stroke and bore you will have problems. Girling; /html/tigers/1998-04/msg00265.html (7,560 bytes)
8. Fw: bellhousing needed (score: 1): Author: "Bob Hokanson" <tgrr2@gte.net>; Date: Wed, 29 Apr 1998 16:57:57 -0700; <rdmallory@earthling.net> make a; /html/tigers/1998-04/msg00269.html (7,941 bytes)

Current List: 1 - 8
Page: [1]