Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*could\s+tire\s+shop\s+have\s+bent\s+my\s+wheel\?\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*could\s+tire\s+shop\s+have\s+bent\s+my\s+wheel\?\s*$/: 8 ]

Total 8 documents matching your query.

1. could tire shop have bent my wheel? (score: 1): Author: james creasy <Black94PGT@pacbell.net>; Date: Fri, 15 Feb 2002 08:44:30 -0800; ive been thinking about my high speed vibration (over 60mph) and measured the runout on my rear wheels. it appears that there is a flat spot on just one spot on the rim (the tire surface reflects thi; /html/ba-autox/2002-02/msg00183.html (7,733 bytes)
2. Re: could tire shop have bent my wheel? (score: 1): Author: Au Nguyen <aunguyen@cisco.com>; Date: Fri, 15 Feb 2002 09:42:14 -0800; I've heard lots of good things about http://www.wheeltechniques.com/ but I've never had to visit them myself. Good luck. Au; /html/ba-autox/2002-02/msg00185.html (8,182 bytes)
3. Re: could tire shop have bent my wheel? (score: 1): Author: "Peter Mottaz" <mph_16@hotmail.com>; Date: Fri, 15 Feb 2002 18:11:14 +0000; Rite-Way Wire & Wheel Specialist 1119 Alpine Road, Walnut Creek, CA 94596 (925) 933-4046 This subject came up on a BMW list recently and this company was one response. I have no personal experience; /html/ba-autox/2002-02/msg00186.html (8,682 bytes)
4. Re: could tire shop have bent my wheel? (score: 1): Author: "John F. Kelly Jr." <76067.1750@compuserve.com>; Date: Fri, 15 Feb 2002 17:47:42 -0500; There also an old-line company called Oakland Rim and Wheel located next door to Broadway Ford just off 24th St. as I recall. I'm sure they can straighten steel rims. The question is: Is it the Wheel; /html/ba-autox/2002-02/msg00187.html (7,569 bytes)
5. Re: could tire shop have bent my wheel? (score: 1): Author: james creasy <Black94PGT@pacbell.net>; Date: Fri, 15 Feb 2002 14:54:06 -0800; what i meant here was i checked the radial runout of the outer rim of the wheel, as well as the tire surface. it was perfectly round, except for one spot. the tire reflect the dip in the wheel. not; /html/ba-autox/2002-02/msg00189.html (8,359 bytes)
6. Re: could tire shop have bent my wheel? (score: 1): Author: "Barry Spencer" <bspencer@tsoft.com>; Date: Fri, 15 Feb 2002 15:21:36 -0800; 1mm is way too much. On a Lotus any more than ,010" will cause a vibration. Have you tired another rim on the same hub. Or, you could try rotating the rim on the lug nuts. Barry -- Original Message; /html/ba-autox/2002-02/msg00191.html (9,131 bytes)
7. Re: could tire shop have bent my wheel? (score: 1): Author: james creasy <Black94PGT@pacbell.net>; Date: Fri, 15 Feb 2002 15:31:28 -0800; good to know... it seemed so little i wasnt sure that was it. rotating wont help... the rim is perfectly round except for one spot. i havent run into any big holes lately so i doubt i could have don; /html/ba-autox/2002-02/msg00192.html (10,371 bytes)
8. Re: could tire shop have bent my wheel? (score: 1): Author: "Debbie" <bartsmom@mindspring.com>; Date: Fri, 15 Feb 2002 16:27:47 -0800; I've used Rite-Way and they were great!! Straightened out some seemingly hopelessly bent rims and did it inexpensively and quickly and with a great attitude! Debbie -- Original Message -- From: "Pete; /html/ba-autox/2002-02/msg00193.html (9,468 bytes)

Current List: 1 - 8
Page: [1]