- 1. m/c (score: 1)
- Author: "Paul A. Dolloff, Ph.D." <pauld@ekpc.com>
- Date: Tue, 5 Oct 1999 13:05:27 EST5EDT
- Can someone give me instructions on how to remove a master cylinder and install the rebuild kit? I'll even call and take instruction over the phone. I'll also check the Puddlejumper. I'm desparate t
- /html/spridgets/1999-10/msg00211.html (7,904 bytes)
- 2. Re: m/c (score: 1)
- Author: Ajhsys@aol.com
- Date: Tue, 5 Oct 1999 13:32:03 EDT
- << Can someone give me instructions on how to remove a master cylinder and install the rebuild kit? I'll even call and take instruction over the phone. I'll also check the Puddlejumper. I'm desparate
- /html/spridgets/1999-10/msg00212.html (8,267 bytes)
- 3. Re: m/c (score: 1)
- Author: bruce@woodward-realty.com
- Date: Tue, 5 Oct 1999 14:07:34 -0000
- I found a 3/4" hone at NAPA, states is for VW brake cylinder. worked on my dual master cylinder perfectly. bruce@woodward-realty.com << Can someone give me instructions on how to remove a master cyli
- /html/spridgets/1999-10/msg00213.html (8,712 bytes)
- 4. Re: m/c (score: 1)
- Author: Ajhsys@aol.com
- Date: Tue, 5 Oct 1999 15:25:24 EDT
- << I found a 3/4" hone at NAPA, states is for VW brake cylinder. worked on my dual master cylinder perfectly. >> - - - - - - - - - - - - - - - - - - - - - - - - I was talking about the clutch MC, whi
- /html/spridgets/1999-10/msg00214.html (7,508 bytes)
- 5. RE: m/c (score: 1)
- Author: "Hanna, Mark" <mhanna@ball.com>
- Date: Tue, 5 Oct 1999 13:55:46 -0600
- Is It ?
- /html/spridgets/1999-10/msg00216.html (8,150 bytes)
- 6. Re: m/c (score: 1)
- Author: Ajhsys@aol.com
- Date: Tue, 5 Oct 1999 17:08:24 EDT
- Come to think of it, I never got the brake MC apart, so I don't know if one is smaller than the other. Think of all the bandwidth I just wasted! Sorry! Allen Hefner '77 Midget '92 Mitsubishi Expo LRV
- /html/spridgets/1999-10/msg00224.html (8,006 bytes)
- 7. Re: m/c (score: 1)
- Author: Bruce Lowry <egnorant@flash.net>
- Date: Tue, 05 Oct 1999 16:07:10 -0400
- Just a "We Tight" tip. For polishing the little bores use a pencil and a strip emory cloth (crocus?) Just duct tape the strip to the end of the pencil and wrap the rest around the pencil. You can eve
- /html/spridgets/1999-10/msg00226.html (8,631 bytes)
- 8. Re: m/c (score: 1)
- Author: "Doug Ingram" <dougi@home.com>
- Date: Tue, 5 Oct 1999 17:52:18 -0700
- I would urge great care and attention in the rebuilding of brake masters, for obvious reasons. The pitting that occurs from moisture in the bore is often far too deep to be honed out. This can leave
- /html/spridgets/1999-10/msg00234.html (9,570 bytes)
- 9. Re: m/c (score: 1)
- Author: "Paul A. Dolloff, Ph.D." <pauld@ekpc.com>
- Date: Wed, 6 Oct 1999 09:07:12 EST5EDT
- Thanks to everyone who emailed helpful hints. After careful consideration, I decided to order rebuilt ones. The cost will be off-set by the time savings but most importantly, the safety factor. No s
- /html/spridgets/1999-10/msg00251.html (10,540 bytes)
This search system is powered by
Namazu