Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*more\s+garage\s+notes\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*more\s+garage\s+notes\s*$/: 14 ]

Total 14 documents matching your query.

1. more garage notes (score: 1): Author: cak@dimebank.com (Chris Kantarjiev); Date: Tue, 9 Jan 1996 22:34:01 -0800; http://pop3.dcc.edu/vettenet/garage.html Has a bunch of notes about building a garage. The first item is rather controversial: whether or not to use PVC for air plumbing. Some folks say it's fine, so; /html/shop-talk/1996-01/msg00022.html (9,195 bytes)
2. RE: more garage notes (score: 1): Author: "Fletcher Blades" <fblades@fanshawe.newzealand.attgis.com>; Date: Thu Jan 11 09:13 NZD 1996; Where I work, (an electronics repair 'shop) we have a 200 foot PVC airline running at about 90-95 psi. There were some teething problems (three years ago) caused by bad glue joints. There has certai; /html/shop-talk/1996-01/msg00028.html (8,419 bytes)
3. RE: more garage notes (score: 1): Author: "Mark Miller" <markm@tutsys.com>; Date: Wed, 10 Jan 1996 14:57:45 -0800; What I remember being told the problem with PVC for air use is not that it may fail but that the failure mode is bad. When it gets cold PVC gets brittle. If it then fails while under pressure (even; /html/shop-talk/1996-01/msg00031.html (8,797 bytes)
4. more garage notes (score: 1): Author: dave.williams@chaos.lrk.ar.us (Dave Williams); Date: Wed, 10 Jan 1996 20:46:00 +0000; If the building is already up and you want to go through the centers of the studs, you have only two choices: PVC and copper. Unless you can cut through the outside of the building to feed pipe thro; /html/shop-talk/1996-01/msg00034.html (9,419 bytes)
5. Re: more garage notes (score: 1): Author: cak@dimebank.com (Chris Kantarjiev); Date: Thu, 11 Jan 1996 22:18:44 -0800; Do you mean that 3/4" copper pipe is flexible enough to feed into the studs, or that it should be cut and spliced? I was planning to notch the studs and put nail plates over, but using copper would b; /html/shop-talk/1996-01/msg00043.html (9,666 bytes)
6. Re: more garage notes (score: 1): Author: Chip Old <fold@mail.bcpl.lib.md.us>; Date: Fri, 12 Jan 1996 12:11:33 -0500 (EST); Semi-rigid 1/2 and 3/4 inch copper pipe can be had in large rolls which can be fed through holes drilled in the studs. You probably won't find semi-rigid pipe at your local Home Depot or Hechinger.; /html/shop-talk/1996-01/msg00050.html (8,922 bytes)
7. Re: more garage notes (score: 1): Author: Chip Old <fold@mail.bcpl.lib.md.us>; Date: Fri, 12 Jan 1996 12:26:40 -0500 (EST); I'm in the midst of redoing mine that way. The risers go up to ceiling level, with hose terminating in quick-connects dropping down to near the floor. That way if I need a quick blast of air to dry; /html/shop-talk/1996-01/msg00052.html (9,821 bytes)
8. Re: more garage notes (score: 1): Author: "Doug Mitchell" <dmitchel@ford.com>; Date: Fri, 12 Jan 1996 13:40:18 -0500; Regarding the use of copper/pvc/black iron pipes for air. We are in the process of modifying the air lines in my facility here at Ford. One of the things that we have done is to add hose reels at the; /html/shop-talk/1996-01/msg00053.html (8,010 bytes)
9. Re: more garage notes (score: 1): Author: cak@aratar.com (Chris Kantarjiev); Date: Fri, 12 Jan 96 11:09:21 PST; My compresser is a large "portable" connected to my air lines via large-diameter hose, I've been wondering about this, too. My compressor is a 25 gallon Craftsman, and all the fittings from the tank; /html/shop-talk/1996-01/msg00054.html (8,185 bytes)
10. Re: more garage notes (score: 1): Author: cak@aratar.com (Chris Kantarjiev); Date: Fri, 12 Jan 96 11:13:33 PST; I'll vouch for hose reels - I have one in my current shop that will reach pretty much any corner (it's a small shop). It's a cheap 50 foot reel from J.C. Whitney; I'm fairly certain it's 1/4 hose, an; /html/shop-talk/1996-01/msg00055.html (8,264 bytes)
11. Re: more garage notes (score: 1): Author: dave.williams@chaos.lrk.ar.us (Dave Williams); Date: Fri, 12 Jan 1996 19:40:00 +0000; If you're on 24" centers you can probably bend the pipe in between two studs. On 16" centers you might wind up notching an adjacent stud to get a little extra room. It's easiest to start in the midd; /html/shop-talk/1996-01/msg00062.html (8,670 bytes)
12. Re: more garage notes (score: 1): Author: dave.williams@chaos.lrk.ar.us (Dave Williams); Date: Sat, 13 Jan 1996 19:42:00 +0000; Today it was 75F, as opposed to snow last Saturday. I spent all day cleaning up out in the shop and the shed. I finally changed the oil in the compressor. Campbell-Hausfeld recommends special Campbe; /html/shop-talk/1996-01/msg00069.html (9,071 bytes)
13. Re: more garage notes (score: 1): Author: dave.williams@chaos.lrk.ar.us (Dave Williams); Date: Sat, 13 Jan 1996 19:48:00 +0000; Gakk! I hate those coiled yellow hoses. If they don't snarl they kink. If you manage to avoid that, they usually have enough tension to whip blowguns and small tools away whenever you lay them down.; /html/shop-talk/1996-01/msg00070.html (8,191 bytes)
14. Re: more garage notes (score: 1): Author: TATERRY@aol.com; Date: Sun, 14 Jan 1996 08:41:17 -0500; Hi Doug, Arnolts almost done! Speaking of hose reels, I bought one of those cheapo ones from Harbor Frieght and mounted it into the center ceiling of the garage/workshop. Surprisingly, it works very; /html/shop-talk/1996-01/msg00073.html (8,109 bytes)

Current List: 1 - 14
Page: [1]