Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*v8\s+bushes\s+vs\s+fulcrum\s+pin\s+fit\?\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*v8\s+bushes\s+vs\s+fulcrum\s+pin\s+fit\?\s*$/: 9 ]

Total 9 documents matching your query.

1. v8 bushes vs fulcrum pin fit? (score: 1): Author: Marc Siegel <smarc@abs.net>; Date: Mon, 20 Jun 2005 10:06:12 -0400; Is there any known issue with Moss supplied V8 bushes not fitting on the fulcrum pin? Out of a set of 4 bushes, only two would slide over the end of the pin... Thinking the pin may have a burr or oth; /html/mgs/2005-06/msg00200.html (7,727 bytes)
2. Re: v8 bushes vs fulcrum pin fit? (score: 1): Author: Charles & Peggy Robinson <ccrobins@ktc.com>; Date: Mon, 20 Jun 2005 09:51:01 -0500; Will the two that fit slide on both pins? When I installed those bushings several years ago I had to sand the rust off the pins. CR; /html/mgs/2005-06/msg00202.html (7,508 bytes)
3. Re: v8 bushes vs fulcrum pin fit? (score: 1): Author: Marc <smarc@abs.net>; Date: Mon, 20 Jun 2005 11:51:50 -0400; I don't recall that I tried that, but will the next chance I get... The pins are absolutely clean - no rust, no burrs... there are in phenomenal shape! I always have these weird problems! I figure it; /html/mgs/2005-06/msg00203.html (7,881 bytes)
4. Re: v8 bushes vs fulcrum pin fit? (score: 1): Author: Marc <smarc@abs.net>; Date: Mon, 20 Jun 2005 13:01:16 -0400; Thanks for that info - I will check the pins with a micrometer to see if perhaps the pin end is flared! -- Marc; /html/mgs/2005-06/msg00205.html (8,358 bytes)
5. Re: v8 bushes vs fulcrum pin fit? (score: 1): Author: "Paul Hunt" <paul.hunt1@blueyonder.co.uk>; Date: Wed, 22 Jun 2005 15:01:40 +0100; If 2 fit the pin and 2 don't then surely it has to be different bores in the PaulH. -- Original Message --; /html/mgs/2005-06/msg00217.html (7,491 bytes)
6. Re: v8 bushes vs fulcrum pin fit? (score: 1): Author: Marc Siegel <smarc@abs.net>; Date: Wed, 22 Jun 2005 10:13:08 -0400; I had a couple hours yesterday to work on the car. I checked the pins, found no flaring at all. Testing the new bushes for fit on the pins shows that two of the four bushes simply did not fit on the; /html/mgs/2005-06/msg00221.html (7,740 bytes)
7. RE: v8 bushes vs fulcrum pin fit? (score: 1): Author: "Dodd, Kelvin" <doddk@mossmotors.com>; Date: Wed, 22 Jun 2005 09:30:31 -0700; Thanks for doing the checking. Sounds like it's time to pull all the bushings from the shelf and check them again. Sigh. It is very frustrating to keep on going over the same issues without getting; /html/mgs/2005-06/msg00227.html (8,576 bytes)
8. Re: v8 bushes vs fulcrum pin fit? (score: 1): Author: Charles & Peggy Robinson <ccrobins@ktc.com>; Date: Thu, 23 Jun 2005 09:11:44 -0500; More "specification drift" Kelvin? I remember my emergency brake cable fiasco. ;^) Er, after sighing, you might send Marc a couple more bushings...... Cheers, CR; /html/mgs/2005-06/msg00248.html (8,605 bytes)
9. RE: v8 bushes vs fulcrum pin fit? (score: 1): Author: "bill king" <bilking@comcast.net>; Date: Thu, 23 Jun 2005 16:54:01 -0400; Can you say six sigma? Or even ISO 9000. Do you have any quality system requirements for your suppliers? I am sure we are paying for Moss Motors having you check to see if your suppliers did their jo; /html/mgs/2005-06/msg00277.html (9,410 bytes)

Current List: 1 - 9
Page: [1]