Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Fot\]\s+TR3\s+TR4\s+REAR\s+ENGINE\s+MOUNTS\s+NEW\s+DESIGN\s+IN\s+THE\s+WORKS\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Fot\]\s+TR3\s+TR4\s+REAR\s+ENGINE\s+MOUNTS\s+NEW\s+DESIGN\s+IN\s+THE\s+WORKS\s*$/: 6 ]

Total 6 documents matching your query.

1. [Fot] TR3 TR4 REAR ENGINE MOUNTS NEW DESIGN IN THE WORKS (score: 1): Author: Joe Alexander <n197tr4@cs.com>; Date: Fri, 9 Mar 2012 09:24:58 -0500 (EST); FOT, For 20 years we have dealt with various motor mounts at the transmission. Once we replaced a motor mount at Road America with material available.....a pine 2 x 4. We are not sure if that wasnt t; /html/fot/2012-03/msg00103.html (10,768 bytes)
2. Re: [Fot] TR3 TR4 REAR ENGINE MOUNTS NEW DESIGN IN THE WORKS (score: 1): Author: malaboge@aol.com; Date: Fri, 9 Mar 2012 11:17:11 -0500 (EST); Fellow motor mounties... Here's something i did ages ago and have never had a mount go "south" since...and even if it did, it wouldn't matter much other than the fact that you'll prolly get some addi; /html/fot/2012-03/msg00106.html (12,754 bytes)
3. Re: [Fot] TR3 TR4 REAR ENGINE MOUNTS NEW DESIGN IN THE WORKS (score: 1): Author: Joe Alexander <n197tr4@cs.com>; Date: Fri, 9 Mar 2012 15:03:18 -0500 (EST); yup, we've done that too. would like to have a nice tidy package that does it all well and be done with it. some have hardmounted the tailshaft, but we'd rather not do that, for a number of reasons.; /html/fot/2012-03/msg00108.html (13,630 bytes)
4. Re: [Fot] TR3 TR4 REAR ENGINE MOUNTS NEW DESIGN IN THE WORKS (score: 1): Author: fubog1 <fubog1@aol.com>; Date: Fri, 9 Mar 2012 16:04:44 -0500 (EST); A short length of "angle iron" with a half inch hole in it fastened under the tailshaft boss on each side, with the flat face butted up against the end of the mount, to take the lateral loads. This i; /html/fot/2012-03/msg00109.html (14,930 bytes)
5. Re: [Fot] TR3 TR4 REAR ENGINE MOUNTS NEW DESIGN IN THE WORKS (score: 1): Author: "Alexandre Camoletti" <ac@camoletti.ch>; Date: Sat, 6 Oct 2012 23:25:44 +0200; Hi Joe! Is this rear mount available finally ? Thank you for your reply! Kind regards AlexC --Message d'origine-- De : fot-bounces@autox.team.net [mailto:fot-bounces@autox.team.net] De la part de Joe; /html/fot/2012-10/msg00046.html (10,282 bytes)
6. Re: [Fot] TR3 TR4 REAR ENGINE MOUNTS NEW DESIGN IN THE WORKS (score: 1): Author: <riverside@southslope.net>; Date: Mon, 8 Oct 2012 09:36:50 -0500; I used a system like this with an old valve spring between flat washers for compliance. A hole in the right place allows a clevis pin to hold it all together and make it quick to disassemble when you; /html/fot/2012-10/msg00050.html (11,870 bytes)

Current List: 1 - 6
Page: [1]