Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Healeys\]\s+Looking\s+for\s+100M\s+Choke\s+abutment\s+bracket\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Healeys\]\s+Looking\s+for\s+100M\s+Choke\s+abutment\s+bracket\s*$/: 8 ]

Total 8 documents matching your query.

1. [Healeys] Looking for 100M Choke abutment bracket (score: 1): Author: "Thomas Willig" <twillig@ruda.de>; Date: Mon, 1 Aug 2011 10:02:55 +0200; can someone enlighten me were I can get a choke abutment bracket for the 100M? I am talking about the small steel strip of flat steel that goes over the entire opening between the two H6 carbs and i; /html/healeys/2011-08/msg00001.html (6,674 bytes)
2. Re: [Healeys] Looking for 100M Choke abutment bracket (score: 1): Author: "Rich Chrysler" <richchrysler@quickclic.net>; Date: Mon, 1 Aug 2011 08:28:23 -0400; I was under the impression it is the same bracket but the end mounting holes are opened up a bit to fit the H6 setup. Rich Hello, can someone enlighten me were I can get a choke abutment bracket for; /html/healeys/2011-08/msg00002.html (8,527 bytes)
3. Re: [Healeys] Looking for 100M Choke abutment bracket (score: 1): Author: "Thomas Willig" <twillig@ruda.de>; Date: Mon, 1 Aug 2011 14:49:14 +0200; no that's not the case (as far as I see it-enlightenment very welcome). The angle of the bracket has to be changed as well. Doing this, you have to cut the bracket were the abutment pin (the pin tha; /html/healeys/2011-08/msg00003.html (9,069 bytes)
4. Re: [Healeys] Looking for 100M Choke abutment bracket (score: 1): Author: Alan Seigrist <healey.nut@gmail.com>; Date: Mon, 1 Aug 2011 21:59:59 +0800; Sounds too complicated! I just opened up the holes a bit like Rich said, that was all I needed. Fit right up. I eventually switched back again (I like the plain jane cars).. Alan -- Sent from my mob; /html/healeys/2011-08/msg00004.html (10,528 bytes)
5. Re: [Healeys] Looking for 100M Choke abutment bracket (score: 1): Author: John Harper <ah@jharper.demon.co.uk>; Date: Mon, 1 Aug 2011 14:58:45 +0100; I think that I agree with Rich on this. It is not easy to make precise measurement but I make the distance between the appropriate holes on a pair of H4s as 6" +- 1/32". The same measurement on a pa; /html/healeys/2011-08/msg00005.html (10,642 bytes)
6. Re: [Healeys] Looking for 100M Choke abutment bracket (score: 1): Author: Tadeusz Malkiewicz <tadeusz.malkiewicz@gmail.com>; Date: Mon, 1 Aug 2011 16:37:14 +0200; I believe Rich is correct. I researched the M setup a bit when installing it on my car, and I fitted the same bracket enlarging the holes. Also, there was no extra bracket in LeMans kit, AFAIK. Tade; /html/healeys/2011-08/msg00006.html (8,642 bytes)
7. [Healeys] Looking for 100M Choke abutment bracket (score: 1): Author: <Josef.Eckert@t-systems.com>; Date: Mon, 1 Aug 2011 16:50:26 +0200; Josef Eckert Konigswinter/Germany --Urspr|ngliche Nachricht-- Von: healeys-bounces@autox.team.net [mailto:healeys-bounces@autox.team.net] Im Auftrag von Alan Seigrist Gesendet: Montag, 1. August 2011; /html/healeys/2011-08/msg00007.html (11,260 bytes)
8. Re: [Healeys] Looking for 100M Choke abutment bracket (score: 1): Author: "Thomas Willig" <twillig@ruda.de>; Date: Tue, 2 Aug 2011 08:22:47 +0200; After checking out the bracket one more time, I can confirm that enlarging the holes is the way to go. I should have known this... My thinking was far too sophisticated J Regards Thomas Willig Von: T; /html/healeys/2011-08/msg00039.html (9,126 bytes)

Current List: 1 - 8
Page: [1]