- 1. [Shop-talk] Removing bondo (score: 1)
- Author: Douglas Braun <doug@dougbraun.com>
- Date: Wed, 19 Oct 2011 19:45:28 -0400
- Hello, I have an old fender (for a '31 Ford) that has a coat of bondo about 1/8" thick all over it. Does anybody know a good way to remove it? I will eventually sandblast the fender, but I am worried
- /html/shop-talk/2011-10/msg00057.html (8,624 bytes)
- 2. Re: [Shop-talk] Removing bondo (score: 1)
- Author: "Eric J Russell" <ejrussell@mebtel.net>
- Date: Wed, 19 Oct 2011 22:41:03 -0400
- Any of those methods will work. Paint stripper is probably the slowest but safest (to the sheet metal). Sandblasting can warp sheet metal. A paint stripping heat gun might be the best compromise. Eri
- /html/shop-talk/2011-10/msg00059.html (8,994 bytes)
- 3. Re: [Shop-talk] Removing bondo (score: 1)
- Author: "Karl Vacek" <kvacek@ameritech.net>
- Date: Wed, 19 Oct 2011 21:57:54 -0500
- Either one will work. Being a Model A fender it's thick enough to take some heat without warping, but no need to heat it very much. Gently heating the underside should loosen it faster than trying to
- /html/shop-talk/2011-10/msg00060.html (9,523 bytes)
- 4. Re: [Shop-talk] Removing bondo (score: 1)
- Author: Bob Spidell <bspidell@comcast.net>
- Date: Wed, 19 Oct 2011 20:02:16 -0700
- A propane torch will soften the filler, making it much easier to scrape the heavier layers off. One of these on a 4.5" grinder will take off the thinner layers: http://www.homedepot.com/buy/paint/pai
- /html/shop-talk/2011-10/msg00061.html (10,280 bytes)
- 5. Re: [Shop-talk] Removing bondo (score: 1)
- Author: Brian Kemp <bk13@earthlink.net>
- Date: Wed, 19 Oct 2011 22:15:06 -0700
- Doug - A wire wheel in an angle grinder will make it all go away real fast. Do it outside when there is a breeze and wear a dust mask or respirator in addition to goggles. It will also save you havin
- /html/shop-talk/2011-10/msg00062.html (10,555 bytes)
- 6. Re: [Shop-talk] Removing bondo (score: 1)
- Author: Douglas Braun <doug@dougbraun.com>
- Date: Thu, 20 Oct 2011 06:44:43 -0400
- Thanks to all for the tips. I'll probably try the wire wheel approach. It can't be messier than sandblasting... Doug _______________________________________________ Shop-talk@autox.team.net Donate: h
- /html/shop-talk/2011-10/msg00064.html (9,168 bytes)
- 7. Re: [Shop-talk] Removing bondo (score: 1)
- Author: Tim <tputland@charter.net>
- Date: Thu, 20 Oct 2011 06:56:18 -0400 (EDT)
- I've removed bondo with a soda blaster; doubly messy with the bondo bits and soda mess, but it did work. tim _______________________________________________ Shop-talk@autox.team.net Donate: http://ww
- /html/shop-talk/2011-10/msg00065.html (10,254 bytes)
- 8. Re: [Shop-talk] Removing bondo (score: 1)
- Author: "John T. Blair" <jblair1948@cox.net>
- Date: Thu, 20 Oct 2011 07:32:22 -0400
- about 1/8" thick all over it. Does anybody fender, but I am worried that the bondo plastics are. Doug, I had a fender like that on my Volvo P1800. What I used was a 4" grinder with a wire wheel on it
- /html/shop-talk/2011-10/msg00066.html (10,012 bytes)
- 9. Re: [Shop-talk] Removing bondo (score: 1)
- Author: PJ McGarvey <pj_mcgarvey@hotmail.com>
- Date: Thu, 20 Oct 2011 09:16:03 -0400
- I'm no expert, but I've done some bodywork using bondo. Unless alot (too much?) hardener is used, wouldn't just sandpaper work? I applied and removed plenty of bondo using an orbital sander attached
- /html/shop-talk/2011-10/msg00067.html (10,277 bytes)
- 10. Re: [Shop-talk] Removing bondo (score: 1)
- Author: "john niolon" <jniolon@bham.rr.com>
- Date: Thu, 20 Oct 2011 10:05:59 -0500
- IF YOU'RE NOT COUGHING UP BONDO DUST FOR THREE DAYS... YOU'RE NOT WORKING HARD ENOUGH !!! _______________________________________________ Shop-talk@autox.team.net Donate: http://www.team.net/donate.h
- /html/shop-talk/2011-10/msg00069.html (11,293 bytes)
- 11. [Shop-talk] Removing bondo (score: 1)
- Author: doug at dougbraun.com (Douglas Braun)
- Date: Wed, 19 Oct 2011 19:45:28 -0400
- Hello, I have an old fender (for a '31 Ford) that has a coat of bondo about 1/8" thick all over it. Does anybody know a good way to remove it? I will eventually sandblast the fender, but I am worried
- /html/shop-talk/2011-10/msg00181.html (8,132 bytes)
- 12. [Shop-talk] Removing bondo (score: 1)
- Author: ejrussell at mebtel.net (Eric J Russell)
- Date: Wed, 19 Oct 2011 22:41:03 -0400
- Any of those methods will work. Paint stripper is probably the slowest but safest (to the sheet metal). Sandblasting can warp sheet metal. A paint stripping heat gun might be the best compromise. Eri
- /html/shop-talk/2011-10/msg00183.html (8,729 bytes)
- 13. [Shop-talk] Removing bondo (score: 1)
- Author: kvacek at ameritech.net (Karl Vacek)
- Date: Wed, 19 Oct 2011 21:57:54 -0500
- Either one will work. Being a Model A fender it's thick enough to take some heat without warping, but no need to heat it very much. Gently heating the underside should loosen it faster than trying to
- /html/shop-talk/2011-10/msg00184.html (9,280 bytes)
- 14. [Shop-talk] Removing bondo (score: 1)
- Author: bspidell at comcast.net (Bob Spidell)
- Date: Wed, 19 Oct 2011 20:02:16 -0700
- A propane torch will soften the filler, making it much easier to scrape the heavier layers off. One of these on a 4.5" grinder will take off the thinner layers: http://www.homedepot.com/buy/paint/pai
- /html/shop-talk/2011-10/msg00185.html (10,114 bytes)
- 15. [Shop-talk] Removing bondo (score: 1)
- Author: bk13 at earthlink.net (Brian Kemp)
- Date: Wed, 19 Oct 2011 22:15:06 -0700
- Doug - A wire wheel in an angle grinder will make it all go away real fast. Do it outside when there is a breeze and wear a dust mask or respirator in addition to goggles. It will also save you havin
- /html/shop-talk/2011-10/msg00186.html (10,350 bytes)
- 16. [Shop-talk] Removing bondo (score: 1)
- Author: doug at dougbraun.com (Douglas Braun)
- Date: Thu, 20 Oct 2011 06:44:43 -0400
- Thanks to all for the tips. I'll probably try the wire wheel approach. It can't be messier than sandblasting... Doug
- /html/shop-talk/2011-10/msg00188.html (8,875 bytes)
- 17. [Shop-talk] Removing bondo (score: 1)
- Author: tputland at charter.net (Tim)
- Date: Thu, 20 Oct 2011 06:56:18 -0400 (EDT)
- I've removed bondo with a soda blaster; doubly messy with the bondo bits and soda mess, but it did work. tim
- /html/shop-talk/2011-10/msg00189.html (9,621 bytes)
- 18. [Shop-talk] Removing bondo (score: 1)
- Author: pj_mcgarvey at hotmail.com (PJ McGarvey)
- Date: Thu, 20 Oct 2011 09:16:03 -0400
- I'm no expert, but I've done some bodywork using bondo. Unless alot (too much?) hardener is used, wouldn't just sandpaper work? I applied and removed plenty of bondo using an orbital sander attached
- /html/shop-talk/2011-10/msg00191.html (9,809 bytes)
- 19. [Shop-talk] Removing bondo (score: 1)
- Author: jniolon at bham.rr.com (john niolon)
- Date: Thu, 20 Oct 2011 10:05:59 -0500
- IF YOU'RE NOT COUGHING UP BONDO DUST FOR THREE DAYS... YOU'RE NOT WORKING HARD ENOUGH !!!
- /html/shop-talk/2011-10/msg00193.html (11,099 bytes)
This search system is powered by
Namazu