Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TR\]\s+Copper\s+head\s+gasket\:\s+Which\s+side\s+up\?\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TR\]\s+Copper\s+head\s+gasket\:\s+Which\s+side\s+up\?\s*$/: 6 ]

Total 6 documents matching your query.

1. [TR] Copper head gasket: Which side up? (score: 1): Author: bill beecher <notakitcar@yahoo.com>; Date: Tue, 21 Jul 2020 16:57:03 -0500; Reassembling the TR3 motor for the old Morgan and I am dry fitting the head gasket. Two questions: 1. Which side goes up, smooth or the rolled over side? 2. On a couple cylinders the gasket protrudes; /html/triumphs/2020-07/msg00115.html (8,757 bytes)
2. Re: [TR] Copper head gasket: Which side up? (score: 1): Author: Tony Drews <tony@tonydrews.com>; Date: Tue, 21 Jul 2020 17:05:53 -0500; Smooth side goes up. It's better if the gasket doesn't protrude, hard to do if the head has been milled at all. I've not messed with the water holes, no firm answer on that one.Â If the edge of thos; /html/triumphs/2020-07/msg00116.html (10,500 bytes)
3. Re: [TR] Copper head gasket: Which side up? (score: 1): Author: TERRY SMITH <terryrs@comcast.net>; Date: Tue, 21 Jul 2020 18:41:54 -0400 (EDT); Just a note: I have made the mistake during earlier rebuilds of not using a succession of half-inch sockets bolted down over the sleeves to ensure each side of the cylinder has compressed the figure; /html/triumphs/2020-07/msg00118.html (12,167 bytes)
4. Re: [TR] Copper head gasket: Which side up? (score: 1): Author: "Jerry Van Vlack" <jerryvv@roadrunner.com>; Date: Tue, 21 Jul 2020 19:30:25 -0400; Adding to what Tony says, the gasket should NOT protrude into the bore. Questions: What is the bore? 86, 87 or 89 mm? Where did the gasket come from and what brand is it? What is it's Part Number? Ho; /html/triumphs/2020-07/msg00119.html (11,764 bytes)
5. Re: [TR] Copper head gasket: Which side up? (score: 1): Author: bill beecher <notakitcar@yahoo.com>; Date: Tue, 21 Jul 2020 18:48:59 -0500; Thank you all, smooth side up it is. Gasket and 87mm pistons and liners all came from TRF, Lucas p/n EC510L. Head and deck are stock. Tony, yes the edge on the water holes are rolled, so Iâ??ll leave; /html/triumphs/2020-07/msg00120.html (12,589 bytes)
6. Re: [TR] Copper head gasket: Which side up? (score: 1): Author: bill beecher <notakitcar@yahoo.com>; Date: Tue, 21 Jul 2020 20:44:36 -0500; My bad, that part number is for a lower end set from BPNW. Bill ï»¿Thank you all, smooth side up it is. Gasket and 87mm pistons and liners all came from TRF, Lucas p/n EC510L. Head and deck are stock; /html/triumphs/2020-07/msg00121.html (12,724 bytes)

Current List: 1 - 6
Page: [1]