- 1. [Tigers] Fuel line support bracket (score: 1)
- Author: awtiger--- via Tigers <tigers@autox.team.net>
- Date: Mon, 2 Feb 2015 12:04:16 -0500
- Hey, guys: My question deals with the under-engine metal fuel line that runs from the bell housing area on the passenger side of the car and curves upward in front of the engine to the fuel filter. I
- /html/tigers/2015-02/msg00002.html (9,826 bytes)
- 2. Re: [Tigers] Fuel line support bracket (score: 1)
- Author: Tom Parker via Tigers <tigers@autox.team.net>
- Date: Mon, 2 Feb 2015 12:38:49 -0500
- Andy, Yeah, a bracket hanging off the bellhousing. It'll take a bit of work, but if you need it, I can get a picture. Tom '67 Mark 2 _______________________________________________ tigers@autox.team.
- /html/tigers/2015-02/msg00003.html (11,083 bytes)
- 3. Re: [Tigers] Fuel line support bracket (score: 1)
- Author: Tom Parker via Tigers <tigers@autox.team.net>
- Date: Mon, 2 Feb 2015 12:56:54 -0500
- Correction: it;s off the lower starter motor bolt. Picture should show up soon. Tom _______________________________________________ tigers@autox.team.net Archive: http://www.team.net/archive Unsubscr
- /html/tigers/2015-02/msg00004.html (11,636 bytes)
- 4. Re: [Tigers] Fuel line support bracket (score: 1)
- Author: Tom Parker via Tigers <tigers@autox.team.net>
- Date: Mon, 2 Feb 2015 13:00:02 -0500
- I had the original steel lines, and when I installed the stainless fuel lines I (more or less) followed the original contours. To keep the line away from the exhaust they routed it below the starter
- /html/tigers/2015-02/msg00005.html (12,378 bytes)
- 5. Re: [Tigers] Fuel line support bracket (score: 1)
- Author: awtiger--- via Tigers <tigers@autox.team.net>
- Date: Mon, 2 Feb 2015 13:56:58 -0500
- Tom: Thank you so much for the picture; I hope it wasn't too much trouble. That will certainly help me, however, with my fuel line routing. I take it that is the only bracket on the line? Is there no
- /html/tigers/2015-02/msg00006.html (12,920 bytes)
- 6. Re: [Tigers] Fuel line support bracket (score: 1)
- Author: Tom Parker via Tigers <tigers@autox.team.net>
- Date: Mon, 2 Feb 2015 14:31:49 -0500
- Andy, The original 2BBL carb connection to the fuel line was a hard - flared fitting on the line directly to the carb, the connection was on the right side (facing front) of the block. So there was o
- /html/tigers/2015-02/msg00007.html (14,898 bytes)
- 7. Re: [Tigers] Fuel line support bracket (score: 1)
- Author: Tom Parker via Tigers <tigers@autox.team.net>
- Date: Mon, 2 Feb 2015 14:40:06 -0500
- Some additional information in case anybody cares... The car has full length headers. The ONLY place the fuel line could safely be run was along the oil pan; anywhere else would have been too close t
- /html/tigers/2015-02/msg00008.html (16,395 bytes)
- 8. Re: [Tigers] Fuel line support bracket (score: 1)
- Author: ironbeast--- via Tigers <tigers@autox.team.net>
- Date: Mon, 2 Feb 2015 22:38:30 +0000 (UTC)
- Andy, There is another metal bracket that mounts to a bolt in the block at the front corner of the engine. Its attached with a horizontal bolt near where the dipstick enters. If I ever replaced it I
- /html/tigers/2015-02/msg00010.html (14,631 bytes)
- 9. Re: [Tigers] Fuel line support bracket (score: 1)
- Author: Tom Parker via Tigers <tigers@autox.team.net>
- Date: Mon, 2 Feb 2015 20:28:19 -0500
- Paul, if convenient I'd like to see a picture of the front fuel line bracket. it's possible the part was eliminated with the transition to the Alternator on the Mark 2, or it may have been lost somew
- /html/tigers/2015-02/msg00011.html (16,190 bytes)
- 10. Re: [Tigers] Fuel line support bracket (score: 1)
- Author: Ron Fraser via Tigers <tigers@autox.team.net>
- Date: Mon, 2 Feb 2015 20:30:13 -0500
- Paul Very interesting! I think I have that bracket on my Tiger but not sure at this moment without looking. I believe that bracket is C3OZ-9180-A. Ron Fraser --Original Message-- From: Tigers [mailto
- /html/tigers/2015-02/msg00012.html (15,007 bytes)
- 11. Re: [Tigers] Fuel line support bracket (score: 1)
- Author: Ron Fraser via Tigers <tigers@autox.team.net>
- Date: Mon, 2 Feb 2015 20:59:35 -0500
- Tom According to the Parts List all Tiger engines have this bracket. I'll have to look on my Tiger but not tonight. Ron Fraser --Original Message-- From: Tigers [mailto:tigers-bounces@autox.team.net]
- /html/tigers/2015-02/msg00013.html (17,386 bytes)
This search system is powered by
Namazu