healeys
[Top] [All Lists]

Re: [Healeys] Instrument panel refinishing

To: Healeys <healeys@autox.team.net>
Subject: Re: [Healeys] Instrument panel refinishing
From: Chester Threedog <chester3dog@gmail.com>
Date: Wed, 1 Apr 2009 13:32:04 -0500
Back in the day...before kids (my son is 27) I had the same problem.  I
followed the instructions on the paint remover can, use thick coat, wait 15
minutes and remove.  It would not even soften that crusty finish.  I tried
again but this time I got called away during my 15 minute wait.  When I
returned 8 hours later  the remover and the finish had crystalized.  Just
scraped it off.  I did this again on a few other BJ8 dashes with same
results.

Grins, Norby

On Tue, Mar 31, 2009 at 10:39 AM, billhuck <billhuck@aol.com> wrote:

>    Some 25 years back I returned a BJ8 dash to its original condition. It
> had
> the normal flaws, fine cracks each bordered by peeling yellowish areas.
> With
> thin sharp tools I peeled off all those areas, maybe a third of the dash. I
> then flowed on a clear 2-part epoxy resin on the peeled areas. The resin
> wet
> the veneer, bringing its color back. It also wet the edges of the original
> epoxy.
>    I used 'EnviroTex Lite', stock #2032, two pint bottles mixed one to
> one..
> Environmental Technology Inc. Fields Landing, CA 95537.
>    I drove the car another five years; the dash remained pristine.     Bill
> Huck,  BN1
>
> On Mar 30, 2009, at 6:14:30 PM, "Michael Hartfield"
> <hartfiel@alumni.princeton.edu> wrote:
> From:   "Michael Hartfield" <hartfiel@alumni.princeton.edu>
> Subject:    Re: [Healeys] Instrument panel refinishing
> Date:   March 30, 2009 6:14:30 PM CDT
> To: Ghess4 <ghess4@cox.net>, healeys@autox.team.net
> I have the same problem. I have used Homer Formby's on furniture in the
> past and it dissolves the existing finish but does not remove it. The
> patina is left intact. They then recommend finishing with Tung Oil which
> can be put on with a rag.
>
>
> Ghess4ghess4@cox.net
>
> > Greetings,
> > Has anyone done a refinish of the Instrument panel on their BJ8? I
> believe
> > that mine are original and appear to have a very heavy epoxy like
> polished
> > appearance however there are a couple of cracks in the finish coating. I
> have
> > found nothing that will soften the finish so that it can be scraped off
> and
> at
> > this point I am afraid to start sanding since it would be difficult to
> tell
> > when the veneer is exposed. Any comments will be greatly appreciated.
> >
> > Gale Hess
> > _______________________________________________
> > Support Team.Net http://www.team.net/donate.html
> >
> > Healeys@autox.team.net
> > http://autox.team.net/mailman/listinfo/healeys
> >
> > You are subscribed as hartfiel@alumni.princeton.edu
> >
> > http://www.team.net/archive
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> You are subscribed as billhuck@aol.com
>
> http://www.team.net/archive
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
>
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> You are subscribed as chester3dog@gmail.com
>
> http://www.team.net/archive
_______________________________________________
Support Team.Net http://www.team.net/donate.html

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys


http://www.team.net/archive

<Prev in Thread] Current Thread [Next in Thread>
  • Re: [Healeys] Instrument panel refinishing, Chester Threedog <=