healeys
[Top] [All Lists]

Re: [Healeys] trans trouble

To: "'PG'" <britishcars@shaw.ca>, "'Ralph Cap'" <rjcapo1@yahoo.com>,
Subject: Re: [Healeys] trans trouble
From: "Tracy Drummond" <bighealey@charter.net>
Date: Thu, 9 Jun 2011 05:48:02 -0700
Paul,

There are two thicknesses of throw out "bearings".  Sounds like you used the
thinner one when you replaced it.  Was the new one thinner than the old one
you pulled?  If so this could be the culprit assuming the clutch plate is in
properly and the hydraulics are all working.

Pull and do over.  It is something simple surely.

Warm Regards,
 
Tracy Drummond
 
PMP | ITIL Service Manager | CISSP | bighealey@charter.net | 408-394-3444
cell | 408-776-0133 home | http://www.linkedin.com/in/tracydrummond

-----Original Message-----
From: healeys-bounces@autox.team.net [mailto:healeys-bounces@autox.team.net]
On Behalf Of PG
Sent: Wednesday, June 08, 2011 2:19 PM
To: 'Ralph Cap'; Healeys@autox.team.net
Subject: Re: [Healeys] trans trouble

When you say "cannot get the car to go into gear", I assume you mean that
it's grinding when you try?

If so, it sounds like your input shaft is rubbing on the pilot bearing which
means that when you depress the clutch, the input shaft is continuing to
spin and as such, the gears will grind when you try to put into gear.

Did you ensure that you had the two Alignment bolts in the correct holes?
Two of the nine bolts that hold the bell housing to the rear engine plate
are a special diameter (slightly smaller than the rest) and are designed to
ensure that the input shaft is aligned exactly correct with the pilot bush.
I believe that these two bolts go in the 7 and 5 o'clock positions when
facing towards the front of the car.....important that these bolts are in
the right holes.

All this being said, you should be able to get the car in gear when it is
not running...might be a little tough depending upon where the input shaft
is aligned when it comes to rest.

Hope this helps.

Paul



-----Original Message-----
From: healeys-bounces@autox.team.net [mailto:healeys-bounces@autox.team.net]
On Behalf Of Ralph Cap
Sent: Wednesday, June 08, 2011 12:19 PM
To: Healeys@autox.team.net
Subject: [Healeys] trans trouble

just installed a new clutch pressure plate bearing and a new slave cylinder
bled the system and cannot get the car to go in gear used the alignment tool
and tightened everything up any sugestions going crazy here
_______________________________________________
Healeys@autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation  $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage:
http://autox.team.net/mailman/options/healeys/britishcars@shaw.ca
_______________________________________________
Healeys@autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation  $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage:
http://autox.team.net/mailman/options/healeys/bighealey@charter.net
_______________________________________________
Healeys@autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation  $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums

<Prev in Thread] Current Thread [Next in Thread>