healeys
[Top] [All Lists]

[Healeys] Fitting a 'Wosp' High torque starter motor.

Subject: [Healeys] Fitting a 'Wosp' High torque starter motor.
From: enquiries at classic-car-world.co.uk (Tom McCay - Classic-Car-World Ltd)
Date: Sun, 26 Jun 2011 00:54:02 +0100
Hi Derek, we are a WOSP reseller for these Hi Torque starter motors and 
hopefully the following should help.

There are two connections on the WOSP starter motor as follows:

 1. Large stud is the main battery post
2. Small spade connection, Ignition switch to the solenoid

 If you are replacing an inertia type starter motor you will have an 
external solenoid connecting to the old starter motor. In normal operation 
turning the ignition key will energise this solenoid and apply a voltage to 
the old starter. Because the WOSP starter comes with its own solenoid you 
need to energise this to operate the motor. There should therefore be a 
small link
 wire between the main battery stud and the small spade connection for the 
solenoid. If it is not fitted you can easily make one of these with a small 
length of wire. With the new starter now in place turning the ignition key 
will again operate your external solenoid as before connecting the voltage 
to the main battery post on the starter and at the same time energise the
 solenoid on the starter.

 If you need anymore information on this please let me know and I can send 
you a wiring diagram.

 Kindest Regards

 Tom
 Tom McCay - Director  Classic-Car-World Ltd, 32 Washingborough Road,
 Heighington, Lincoln, LN4 1RE. 01522 888178 (Tel) 0870 705 9115 (fax)
 enquiries at ccw-tools.com  www.ccw-tools.com

 Registered address: 32 Washingborough Road, Heighington, Lincoln, LN4 1RE.
 Classic-Car-World Limited is a company registered in England and Wales with
 company number 3930761.  VAT registration number: 755 7630 05

 ----- Original Message ----- 
> From: "Derek Job" <derek.c.job at gmail.com>
> To: "Forum" <Healeys at autox.team.net>
> Sent: Saturday, June 25, 2011 8:43 PM
> Subject: [Healeys] Fitting a 'Wosp' High torque starter motor.
>
>
>>I want to fit my newly acquired High Torque motor but I want to be sure
>> about the wiring and positioning.
>>
>> My car is positive earth and still has an inertia motor and starter
>> solenoid. Not being very electrically inclined I'm slightly confused by 
>> the
>> wording in Wosp's instructions. They say.
>>
>> 'Where our starter directly replaces an inertia type original fitment
>> starter motor *we will fit* the unit with a link wire between the 
>> ignition
>> trigger terminal and the battery stud post.'
>>
>> I ordered mine from AH Spares for an Austin Healey, do I therefore assume
>> that this link wire has already been fitted?. I'm thinking that this 
>> might
>> be the case and all I have to do is fit the main power cable to the stud
>> post. Anyone fitted a Wosp motor?
>>
>> Silly question probably, but can these accidently be fitted upside down?
>>
>> cheers
>>
>> Derek
>> _______________________________________________
>> Healeys at autox.team.net
>> Donate: http://www.team.net/donate.html
>> Suggested annual donation  $12.75
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Unsubscribe/Manage: 
>> http://autox.team.net/mailman/options/healeys/enquiries at 
>> classic-car-world.co.uk

<Prev in Thread] Current Thread [Next in Thread>