healeys
[Top] [All Lists]

Re: [Healeys] BJ8 Radiator Drain

To: r3m1g4@verizon.net, Healeys@autox.team.net
Subject: Re: [Healeys] BJ8 Radiator Drain
From: Larry Wendland <bighealey3k@aim.com>
Date: Sat, 10 Nov 2012 18:45:54 -0500 (EST)
Delivered-to: mharc@autox.team.net
Delivered-to: healeys@autox.team.net
References: <000d01cdb515$8288b370$879a1a50$@net> <8CF8363068975AC-384-4A18A@webmail-m004.sysops.aol.com> <003001cdbf8c$88e13680$9aa3a380$@net>
Mike,  It crossed my mind after I replied to you earlier, that someone may
have forced a pipe threaded drain valve in to the bottom of the radiator and
in doing so, reshaped the threads or used a pipe tap.  If it doesn't leak,
that is a good thing.

Larry
'67 BJ8


-----Original Message-----
From: Mike Garvey <r3m1g4@verizon.net>
To: Healeys <Healeys@autox.team.net>
Sent: Sat, Nov 10, 2012 4:48 pm
Subject: Re: [Healeys] BJ8 Radiator Drain


Maybe just to close the chapter on this:



I was never able to get a tight seal using the (machine thread) shutoff
(with fiber washer) from Moss.

I finally opted for a shutoff that I got from a local radiator shop which
had a <-18NPT thread.

Mike



Michael Garvey

1967 BJ8/38046

Swampscott, MA



From: Larry Wendland [mailto:bighealey3k@aim.com]
Sent: Sunday, October 28, 2012 4:36 PM
To: r3m1g4@verizon.net; Healeys@autox.team.net
Subject: Re: [Healeys] BJ8 Radiator Drain



Mike,  It has been many years since I had my radiator drain tap removed, but
as I remember it is right hand threaded and is a machine thread (straight
thread).  I don't remember the size and threads per inch.  The drain tap in
the side of the block behind and below the exhaust manifold is the same type
of tap and is interchangeable as I remember.  They both use the fiber
washers to seal them.  I've seen two fiber washers, if needed, used on the
block drain tap to get it clocked the right way so as not to over torque it
in order to get it vertical (handle on top and drain hole on bottom).



Larry

'67 BJ8

-----Original Message-----
From: Mike Garvey <r3m1g4@verizon.net>
To: Healeys <Healeys@autox.team.net>
Sent: Sun, Oct 28, 2012 10:13 am
Subject: [Healeys] BJ8 Radiator Drain

I need to replace the radiator drain on my BJ8.  The existing drain (which
is a tubular left-hand-threaded concentric bore arrangement) appears to have
pipe threads (ie tapered threads and sealed with sealant) which mate to the
radiator.



The replacement tap (which is a rotary valve with handle) that I have
received from Moss (pn 460-020) is sealed with a fiber washer(pn 324-671); I
am unsure if the new drain has tapered threads.



I am sure someone has been down this road and can advise me on whether I
have the correct replacement parts from Moss.



Thanks in advance, Mike



Michael Garvey

1967 BJ8/38046

Swampscott, MA
Archive: http://www.team.net/archive

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys

http://autox.team.net/mailman/options/healeys/bighealey3k@aim.com
Archive: http://www.team.net/archive

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys

http://autox.team.net/mailman/options/healeys/bighealey3k@aim.com
_______________________________________________
Archive: http://www.team.net/archive

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys


<Prev in Thread] Current Thread [Next in Thread>