--===============7675541814367527873==
--000000000000a02cbc059bf8e8ac
Content-Transfer-Encoding: quoted-printable
David
I can add a similar problem to that which you identified where there were
100 sump gaskets on the market that did not a have a hole where the oil
behind the valve could get away resulting in the relief valve not operate
correctly.
If the valve did not 'relief' then oil pressure could rise way above the
safe reading. This could cause the pump to have to work harder and the
stain on the pump, pump shaft and cam shaft could cause damage.
Best regards
On Sun, 12 Jan 2020 at 19:21, David Nock <healeydoc@sbcglobal.net> wrote:
> The spring should fit into the hole in the plug and the valve.
> There is a bleed hole on the back side of the valve that drains back int
> the oil pan. It sit in the in debt of the oil pan. I have seen some alloy
> pans that block the hole. Also have seen people use excessive silicone an=
d
> plu the hole up.
>
> David Nock
>
> Sent from my iPhone
>
> On Jan 12, 2020, at 9:41 AM, jpaynepbr@cox.net wrote:
>
> =EF=BB=BF
>
> My recently rebuilt AH 3000 with new oil pump is putting out 100 psi of
> oil pressure at startup and is at an easy 50 to 60 psi at idle when heate=
d
> up.
>
>
>
> It is my understanding that the oil pressure release valve is set to not
> exceed 60 psi?
>
>
>
> I pulled it out, and my question is, is the spring supposed to sit down
> inside the machined hole in the plug or is the spring supposed to sit on
> the lip of the plug and not go down into the hole.
>
>
>
> <image001.jpg>
>
> Jonas
>
>
>
>
>
> *From:* Jonas Payne <jpayne@jpaynepbr.onmicrosoft.com>
> *Sent:* Sunday, January 12, 2020 9:32 AM
> *To:* Jonas Payne <jpayne@jpaynepbr.onmicrosoft.com>
> *Subject:* Pic
>
>
>
>
>
>
>
> Get Outlook for Android <https://aka.ms/ghei36>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
>
> Archive: http://www.team.net/pipermail/healeys
> http://autox.team.net/archive
>
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/healeydoc@sbcglobal.net
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
>
> Archive: http://www.team.net/pipermail/healeys
> http://autox.team.net/archive
>
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/ah100register@gmail.com
>
>
--=20
Best wishes
John Harper
AHC UK 100 Register Secretary
--000000000000a02cbc059bf8e8ac
Content-Transfer-Encoding: quoted-printable
<div dir=3D"ltr">David<div><br></div><div>I can add a similar problem to th=
at which you identified where there were 100 sump gaskets on the market tha=
t did not a have a hole where the oil behind=C2=A0the valve could=C2=A0 get=
away resulting in the relief=C2=A0valve not operate correctly.</div><div><=
br></div><div>If the valve did not 'relief' then oil pressure could=
rise way above the safe reading. This could cause the pump to have to work=
harder and the stain on the pump, pump shaft and cam shaft could cause dam=
age.</div><div><br></div><div>Best regards</div></div><br><div class=3D"gma=
il_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Sun, 12 Jan 2020 at 19:2=
1, David Nock <<a href=3D"mailto:healeydoc@sbcglobal.net";>healeydoc@sbcg=
lobal.net</a>> wrote:<br></div><blockquote class=3D"gmail_quote" style=
=3D"margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding=
-left:1ex"><div dir=3D"auto">The spring should fit into the hole in the plu=
g and the valve.=C2=A0<div>There is a bleed hole on the back side of the va=
lve that drains back int the oil pan. It sit in the in debt of the oil pan.=
I have seen some alloy pans that block the hole. Also have seen people use=
excessive silicone and plu the hole up.=C2=A0<br><br><div dir=3D"ltr"><div=
>David Nock</div><div><br></div>Sent from my iPhone</div><div dir=3D"ltr"><=
br><blockquote type=3D"cite">On Jan 12, 2020, at 9:41 AM, <a href=3D"mailto=
:jpaynepbr@cox.net" target=3D"_blank">jpaynepbr@cox.net</a> wrote:<br><br><=
/blockquote></div><blockquote type=3D"cite"><div dir=3D"ltr">=EF=BB=BF<div>=
<p class=3D"MsoNormal">My recently rebuilt AH 3000 with new oil pump is put=
ting out 100 psi of oil pressure at startup and is at an easy 50 to 60 psi =
at idle when heated up.<u></u><u></u></p><p class=3D"MsoNormal"><u></u>=C2=
=A0<u></u></p><p class=3D"MsoNormal">It is my understanding that the oil pr=
essure release valve is set to not exceed 60 psi?<u></u><u></u></p><p class=
=3D"MsoNormal"><u></u>=C2=A0<u></u></p><p class=3D"MsoNormal">I pulled it o=
ut, and my question is, is the spring supposed to sit down inside the machi=
ned hole in the plug or is the spring supposed to sit on the lip of the plu=
g and not go down into the hole.<u></u><u></u></p><p class=3D"MsoNormal"><u=
></u>=C2=A0<u></u></p><p class=3D"MsoNormal"></p><div><image001.jpg><=
/div><u></u><u></u><p></p><p class=3D"MsoNormal">Jonas<u></u><u></u></p><p =
class=3D"MsoNormal"><u></u>=C2=A0<u></u></p><p class=3D"MsoNormal"><u></u>=
=C2=A0<u></u></p><div><div style=3D"border-right:none;border-bottom:none;bo=
rder-left:none;border-top:1pt solid rgb(225,225,225);padding:3pt 0in 0in"><=
p class=3D"MsoNormal"><b>From:</b> Jonas Payne <<a href=3D"mailto:jpayne=
@jpaynepbr.onmicrosoft.com" target=3D"_blank">jpayne@jpaynepbr.onmicrosoft.=
com</a>> <br><b>Sent:</b> Sunday, January 12, 2020 9:32 AM<br><b>To:</b>=
Jonas Payne <<a href=3D"mailto:jpayne@jpaynepbr.onmicrosoft.com"; target=
=3D"_blank">jpayne@jpaynepbr.onmicrosoft.com</a>><br><b>Subject:</b> Pic=
<u></u><u></u></p></div></div><p class=3D"MsoNormal"><u></u>=C2=A0<u></u></=
p><p class=3D"MsoNormal" style=3D"background:white"><span style=3D"color:rg=
b(33,33,33)"><br><br><u></u><u></u></span></p><div id=3D"gmail-m_3910667989=
44367873ms-outlook-mobile-signature"><div><p class=3D"MsoNormal"><u></u>=C2=
=A0<u></u></p></div><p class=3D"MsoNormal">Get <a href=3D"https://aka.ms/gh=
ei36" target=3D"_blank">Outlook for Android</a><u></u><u></u></p></div></di=
v><span>_______________________________________________</span><br><span>Sup=
port Team.Net <a href=3D"http://www.team.net/donate.html"; target=3D"_blank"=
>http://www.team.net/donate.html</a></span><br><span>Suggested annual donat=
ion =C2=A0$12.75</span><br><span></span><br><span>Archive: <a href=3D"http:=
//www.team.net/pipermail/healeys" target=3D"_blank">http://www.team.net/pip=
ermail/healeys</a> <a href=3D"http://autox.team.net/archive"; target=3D"_bla=
nk">http://autox.team.net/archive</a></span><br><span></span><br><span><a h=
ref=3D"mailto:Healeys@autox.team.net"; target=3D"_blank">Healeys@autox.team.=
net</a></span><br><span><a href=3D"http://autox.team.net/mailman/listinfo/h=
ealeys" target=3D"_blank">http://autox.team.net/mailman/listinfo/healeys</a=
></span><br><span></span><br><span>Unsubscribe/Manage: <a href=3D"http://au=
tox.team.net/mailman/options/healeys/healeydoc@sbcglobal.net" target=3D"_bl=
ank">http://autox.team.net/mailman/options/healeys/healeydoc@sbcglobal.net<=
/a></span><br><span></span><br></div></blockquote></div></div>_____________=
__________________________________<br>
rer" target=3D"_blank">http://www.team.net/donate.html</a><br>
<br>
Archive: <a href=3D"http://www.team.net/pipermail/healeys"; rel=3D"noreferre=
r" target=3D"_blank">http://www.team.net/pipermail/healeys</a> <a href=3D"h=
ttp://autox.team.net/archive" rel=3D"noreferrer" target=3D"_blank">http://a=
utox.team.net/archive</a><br>
<br>
<a href=3D"mailto:Healeys@autox.team.net"; target=3D"_blank">Healeys@autox.t=
eam.net</a><br>
<a href=3D"http://autox.team.net/mailman/listinfo/healeys"; rel=3D"noreferre=
r" target=3D"_blank">http://autox.team.net/mailman/listinfo/healeys</a><br>
<br>
s/ah100register@gmail.com" rel=3D"noreferrer" target=3D"_blank">http://auto=
x.team.net/mailman/options/healeys/ah100register@gmail.com</a><br>
<br>
</blockquote></div><br clear=3D"all"><div><br></div>-- <br><div dir=3D"ltr"=
class=3D"gmail_signature"><div dir=3D"ltr">Best wishes<div><br></div><div>=
John Harper</div><div><br></div><div>AHC UK 100 Register Secretary</div></d=
iv></div>
--000000000000a02cbc059bf8e8ac--
--===============7675541814367527873==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============7675541814367527873==--
|