spridgets
[Top] [All Lists]

Re: fuel tank cleaner [2]

To: "Spridgets" <spridgets@autox.team.net>
Subject: Re: fuel tank cleaner [2]
From: "Larry Miller" <millerls@email.msn.com>
Date: Tue, 19 Jan 1999 14:58:59 -0800
Reply-to: "Larry Miller" <millerls@email.msn.com>
Sender: owner-spridgets@autox.team.net
The sock is just a filter and a poor one at that.  Renu told me that they
take it off and leave it off when they do a tank. You are much better off
with an in-line filter which I think most people have anyway.

Larry Miller
-----Original Message-----
From: Michael Dietsche <mdietsche@yahoo.com>
To: MG List <spridgets@autox.team.net>
Date: 19 January, 1999 2:49 PM
Subject: Re: fuel tank cleaner [2]


>--0-1801979802-916784762=:14345
>Content-Disposition: inline
>
>
>
>note: forwarded msg attached.
>
>
>
>--0-1801979802-916784762=:14345
>
>Received: from [12.13.226.15] by send106.yahoomail.com; Tue, 19 Jan 1999
14:21:07 PST
>Date: Tue, 19 Jan 1999 14:21:07 -0800 (PST)
>From: Michael Dietsche <mdietsche@yahoo.com>
>Subject: Re: fuel tank cleaner [2]
>To: Christopher Palmer <ctp@gbn.org>
>MIME-Version: 1.0
>Content-Length: 3403
>
>
>
>I think the screen you refer to is what my radiator shop guy called a
>"small sock" -- he lost it when he took the pickup tube out.  I had my
>tank dip-cleaned, then the radiator shop soldered some pinholes and
>lined the tank with the plastic slosh treatment.  He took the pickup
>tube out prior to sloshing and lost the screen in the process.  My
>tank has a slotted tab pointed up from the bottom to hold the tube in
>place while you tighten the connection.  I just centered the tube end
>in the tab (minus the original screen, of course), then CAREFULLY put
>the tank in place and SLOWLY tightened the fitting, hoping the tube
>wouldn't spin around to the wrong position in the process.  If you
>keep the thing oriented horizontal the tube will stay put in the tab
>and you can tighten it up without it spinning up out of place.
>
>I assume the screen helps hold the tube in position in the slotted tab
>so you don't have to go through the above gyrations.  If the tube can
>be popped loose and back in place easily you might want to pop it up
>and tape it away from the bottom while you slosh.  Or take the tube
>out altogether if the screen goes off and on easy -- I don't know
>about that since I never saw mine, but I think it has to come off to
>get the tube out of the tank.  Alternatively, I guess you could leave
>the tube in place for the sloshing and blow air through the tube to
>clear it before it hardens.....admittedly a little scary cause if it
>blocks the tube and hardens you might have to take the tube out to
>clear it anyway....The slosh stuff is pretty thick goop and I'd bet
>you'd foul the screen with it if the tube is in place during the
>slosh.....I'd even be spooked about it gluing the tube assembly to the
>bottom of the tank!
>
>MD
>
>
>
>---Christopher Palmer <ctp@gbn.org> wrote:
>>
>> Also...In the Spridget fuel tank (at least in mine) there is a little
>> screen cage on the bottom of the pickup tube.  After seeing how
>close to
>> the bottom of the tank it was (as it should be) I was hesitant to
>use any
>> sealant for fear of clogging up that screen.
>>
>> Anyone have any experience sealing one of these tanks and it not
>affecting
>> the screen?
>>
>> CTP
>>
>> At 12:01 PM -0800 1/19/99, Larry Miller wrote:
>> >What Moss sells is actually a three part process. Cleaner, etcher,
>and
>> >sealer.  The cleaner is just a heavy duty de-greaser and would not
>even
>> >touch the tank I tried it on.  Never tried the other two products.
>> >
>> >Larry Miller
>> >-----Original Message-----
>> >From: Christian Stanton <cstanton@pixley.com>
>> >To: Spridgets@autox.team.net <Spridgets@autox.team.net>;
>samesq@pacbell.net
>> ><samesq@pacbell.net>
>> >Date: 19 January, 1999 11:56 AM
>> >Subject: Re: fuel tank cleaner
>> >
>> >
>> >>By fuel tank cleaner I assume you mean a two part etchant/sealer
>product.
>> >>
>> >>I used the fuel tank kit from JC Whitney to clean and coat the
>inside of
>> >the tank for my '68 Saab.  I am very pleased with the results.  The
>etchant
>> >is just dilute acid (of the type that has been discussed under the
>RUST
>> >thread) and the coating is a two part MEK based thick paint.  Just
>make sure
>> >to blow out the gas pickup and vents with air _before_ this stuff
>sets up.
>> >>
>> >>My guess is that the Moss kit is the same stuff.
>> >>
>> >>
>>
>>
>>
>>
>
>
>
>
>
>--0-1801979802-916784762=:14345--
>




<Prev in Thread] Current Thread [Next in Thread>