spridgets
[Top] [All Lists]

Re: tilton, or other jim-crack clutches

To: <Editorgary@aol.com>
Subject: Re: tilton, or other jim-crack clutches
From: "David Wingett" <elkhorn@core.com>
Date: Mon, 28 Mar 2005 12:11:36 -0500
Cc: "Friend Of Triumph" <FOT@autox.team.net>
Delivered-to: mharc@demo.fatchancegarage.com
References: <1c4.250426e1.2f78cc6e@aol.com>
Reply-to: "David Wingett" <elkhorn@core.com>
Sender: owner-fot@autox.team.net
Bob
        Tilton has given up on making Triumph flywheels.  They will however
do one off stuff at there shop rate.  I have been using a 7 1/4" OTII for
some time and am looking for something else, like a 5.5" disk.

        Tilton makes both a 5.5" button clutch which has no flywheel and a
clutch assembly for a conventional flywheel.  Check out there web site.
They have assembly drawings with some basic dimensions.  What I'm thinking
of doing is to ask Tilton to make a button clutch with our crank bolt
pattern and shaft diameter and making a flex plate myself for the button
clutch.   I've already looked at cutting down the Stock flywheel for the
flexplate.  The second thought , is to just make a friction pressure plate
flywheel with an integrated ring gear. The gear could be cut with a wire
feed cutter ( ECM ).  If I can find all the proper dimensions for the gear.
My thought is that this can be done. Creg Taylor at Taylor racing has
allready made for me a bell housing with an adjustable throw-out bearing.

        My daughter and her team at Western Mich. had done some basic foot
work on this project.  But it seems there senior paper is now going towards
studying the molecular structure, friction properties, shear & torque stuff
bla,bla bla..(Way over my head ) of the material used.   Not the design /
development & assembly of  MY NEW CLUTCH ASSEMBLY.   This what I get when
you asking a rocket sciencetest to build a hammer.  So it's back in my
court.....

        May be there are others of our group interested in something like
this?   Just looking for input here, I have most of the dimensions and can
get most of the work done.   Thoughts?

            David W.
            TR6  E/P


----- Original Message ----- 
From: <Editorgary@aol.com>
To: <fot@autox.team.net>
Sent: Sunday, March 27, 2005 9:56 PM
Subject: tilton, or other jim-crack clutches


> In a message dated 3/27/05 6:25:37 PM, owner-fot-digest@autox.team.net
> writes:
>
>
> >
> > BOB KRAMER <rkramer3@austin.rr.com> wrote:
> > Do any USA suppliers sell the fancy, lightweight billet steel
> > flywheel/Tilton race clutch setups ?
> >
> Can't speak for Triumphs, but after four years of fighting it (clutch
> slipping, engagement too quick for paddock and trailer loading, very thin
clutch
> plate, linkage difficult to get positioned properly, etec. etc.), I pulled
the
> Tilton clutch and lightweight flywheel off my MGA and installed a standard
> Moss-sourced MGB clutch. Made the decision when I asked a five-time SCCA
national
> champion what he was running on his MGA. His thought is that if you get
too
> light on our less than precise engines--especially the three-main MGA
engine, you
> take away some of the mass that helps keep the engine running smoothly -- 
> which is, of course, why there is a flywheel there in the first place.
Don't know
> how much of that translates across to Triumphs, but that is one decidely
> non-vintage upgrade that may not be the best thing for an ancient
"agricultural"
> (that's an adjective, not a Ferguson fact, folks) engine.
> Cheers
> Gary
>
>
>
> _____________________________________________________
> This message scanned for viruses by CoreComm

<Prev in Thread] Current Thread [Next in Thread>