spridgets
[Top] [All Lists]

Re: [Spridgets] favorite tools iin shop

To: spridgets list <spridgets@autox.team.net>
Subject: Re: [Spridgets] favorite tools iin shop
From: brian S <bugeye15@hotmail.com>
Date: Sun, 14 Feb 2010 11:36:28 -0500
What Phil said.....:-)

I have a benchtop Horrible Freight blast cabinet, Top Loader.
Not real big, but good for 80% of the stuff I did for my Bugeye.
Top Load doesn't seal real well, I always wear a mask.
I was amazed at the stuff on the outside of even just a medium dust mask.
I'm always wiping the plastic "window" down to see in.
Constantly pushing the glass beads back down to the bottom.
I have a 2 hp 30 gallon Craftsman 110 compressor pushing it.
Can't blast very long w/o it kicking on.
My shop vac sucks the gloves into the cabinet if I don't severely restrict
it's
flow with tape over the hose.

Now, despite all this, it was one of the best things I bought
to restore my Bugeye.
Saved tons of time and money cleaning things myself.
I would get a better cabinet if I had to do it again, but it was only $100.

A gentleman who runs a blasting supply company and my
stepfather who used to run a machine shop recommend glass beads
as the best all around media if you don't want to constantly change media
out.
Can be used on just about everything.

my 2 cents

Brian S.
Bugeyeracer finally resto'ed!



> From: nases@verizon.net
> Date: Sun, 14 Feb 2010 09:35:29 -0500
> To: mdrowe@optonline.net
> CC: spridgets@autox.team.net
> Subject: Re: [Spridgets] favorite tools iin shop
>
> On Feb 14, 2010, at 8:47 AM, Michael Rowe wrote:
>
> > There is near universal agreement on a blast cabinet.   This week I
> completed the 220v line for my $150, 60 gal Craig's List Special
compressor.
> There is a large range of sizes and prices for blast cabinets.  What
features
> are essential?  Does anyone use cheap sand instead of glass beads?
> >
> > Michael Rowe
>
> What size you need depends on what your blasting of course. Mine just
barely
> allows a road wheel to be worked on but it won't allow a anti-roll bar
sized
> part.  To be sure you need good lighting inside,  if the seams aren't
already
> sealed then do it yourself before it gets dirty.  On my bench top the
hopper
> sides aren't steep enough so I'm constantly pushing media down to the
pickup
> tube so my next one will be a floor stand type which allows steeper sides
on
> the hopper.  Mine has a side door which leaks media,  I haven't used the
top
> loaders but it seems logical they would be less prone to leaks.  Also build
> yourself a dust bong like Frank uses to keep the dust out of the air and
save
> your vacuum from early failure.  I think Frank had the plans on the
Teglerizer
> site on how to do it, not sure if it's still there.
>
> If you use sand wear a good quality respirator, I use one even with glass
> beads.  I think sand also builds up a lot of heat on the material and can
warp
> it.  I get by using glass on most stuff.
>
> Phil Nase
> Quakertown, PA
> http://home.comcast.net/~philnasecpa/
>
>

_________________________________________________________________
Your E-mail and More On-the-Go. Get Windows Live Hotmail Free.
http://clk.atdmt.com/GBL/go/201469229/direct/01/

_______________________________________________
Support Team.Net  http://www.team.net/donate.html

Suggested annual donation $12.75


http://www.team.net/archive

http://autox.team.net/mailman/listinfo/spridgets

<Prev in Thread] Current Thread [Next in Thread>