tigers
[Top] [All Lists]

Re: [Tigers] =?utf-8?q?The_real_reasons_I_wanted_to_post?=

To: "=?utf-8?B?Um9uIEZyYXNlcg==?="
Subject: Re: [Tigers] =?utf-8?q?The_real_reasons_I_wanted_to_post?=
From: "=?utf-8?B?c3Bvb2swMUBjb21jYXN0Lm5ldA==?=" <spook01@comcast.net>
Date: Wed, 30 Jun 2010 21:22:31 -0500
The bumper bolts are a very dangerous way to hang these cars. Weld up a square 
tube front and rear subframe to carry the load. In the front I used the front 
four suspension bolts to hook up, and in the rear used the front and rear 
spring mounting. 
These areas carry the load normally, and it worked a treat for me. 

Sent from my Verizon Wireless Phone

----- Reply message -----
From: " Ron Fraser" <rfraser@bluefrog.com>
Date: Wed, Jun 30, 2010 20:59
Subject: [Tigers] The real reasons I wanted to post
To: "'Tom Parker'" <tkparker1941@gmail.com>, "'Al Fudge'" 
<allfudge1635@gmail.com>
Cc: <tigers@autox.team.net>


        IMO, the jack holes and bumper bolts are a poor choose to mount the
rotisserie.  This is mostly folded sheet metal and a small bolt holding the
car; this could fail.   The crossmember bolts or the engine mounting bolt
area is much stronger in front and the leaf spring bolts for the rear.

        I did not have my Tiger on a rotisserie so I hope those who have
will confirm these statements.

Ron Fraser

-----Original Message-----
From: tigers-bounces@autox.team.net [mailto:tigers-bounces@autox.team.net]
On Behalf Of Tom Parker
Sent: Wednesday, June 30, 2010 8:15 PM
To: Al Fudge
Cc: tigers@autox.team.net
Subject: Re: [Tigers] The real reasons I wanted to post


Al,

I bead blasted mine. If I had it to do all over I think I'd have it dipped.
There were seams that weren't cleaned out enough. It may have been an
operator problem, but I suspect it's just the way bead blasting is.

I have an AutoTwirler rotisserie and I like it. We made custom Sunbeam
mounts that use the jack holes and bumper bolts. It worked really well
except when the body was finally straight they had to "adjust" the brackets.

Sadly the brackets are no more; they didn't make it back from the body shop.

Tom

Just for grins, where are you located? I'm in Georgia.


On Wed, Jun 30, 2010 at 6:42 PM, Al Fudge <allfudge1635@gmail.com> wrote:

> I have a couple of questions for the community. I am 99.5% done with
> dissassembling my MK1.  It needs some rust repair and I am considering
> having the shell soda blasted.  Any comments on the relative merits of
> soda blasting over bead or sand blasting?  I want to strip the shell
> to bare metal so I can determine the extent of the required repairs,
> and there will be more than a few.
>
> Also, what about rotisseries?  I have looked at the Auto twirler, but
> are there any others to consider? I don't want to build one; I'd
> rather buy a complete one.
>
> Thanks,
>
> Al
> B9471635
> _______________________________________________
> Tigers@autox.team.net
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/tigers/tkparker1941@gmail.com
_______________________________________________
Tigers@autox.team.net
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage:
http://autox.team.net/mailman/options/tigers/rfraser@bluefrog.com
_______________________________________________
Tigers@autox.team.net
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums

<Prev in Thread] Current Thread [Next in Thread>
  • Re: [Tigers] =?utf-8?q?The_real_reasons_I_wanted_to_post?=, =?utf-8?B?c3Bvb2swMUBjb21jYXN0Lm5ldA==?= <=