--===============6699595329822386823==
boundary="----=_Part_9084117_1272885732.1553213597043"
------=_Part_9084117_1272885732.1553213597043
Content-Transfer-Encoding: quoted-printable
just a couple comments about the wheel alignment current discussion...almos=
t all auto manufactures have recommended weight applications for doing an a=
lignment, you would have to look far and wide to find a shop that does it, =
that being said most experienced techs can align the vehicle to perform wel=
l and obtain acceptable tire wear..secondly I can't comment on toe out as i=
t pertains to a Tiger, =C2=A0but I can tell you that in my experience with =
regular modern passenger cars today the toe out condition usually causes th=
e car to not tract very well and it will dart from side to side with steeri=
ng input, and if excessive will cause abnormal tire wear to the inside edge=
..specialty shops for performance modern cars probably will weight the car =
to the drivers average occupancy of the car, I worked in a Porsche shop man=
y years ago and we did it, but most of those cars had suspension mods for a=
uto cross and track days....today when I do my cars at the shop I sit in th=
e drivers seat for for final settings..members out there could probably do =
that at your local tire shop, =C2=A0just ask
-----Original Message-----
From: tigers-request <tigers-request@autox.team.net>
To: tigers <tigers@autox.team.net>
Sent: Thu, Mar 21, 2019 5:58 pm
Subject: Tigers Digest, Vol 11, Issue 111
Send Tigers mailing list submissions to
=C2=A0=C2=A0=C2=A0 tigers@autox.team.net
To subscribe or unsubscribe via the World Wide Web, visit
=C2=A0=C2=A0=C2=A0 http://autox.team.net/mailman/listinfo/tigers
or, via email, send a message with subject or body 'help' to
=C2=A0=C2=A0=C2=A0 tigers-request@autox.team.net
You can reach the person managing the list at
=C2=A0=C2=A0=C2=A0 tigers-owner@autox.team.net
When replying, please edit your Subject line so it is more specific
than "Re: Contents of Tigers digest..."
Today's Topics:
=C2=A0 1. Re: 66 MK 1A Wheel Alignment (Tom Witt)
----------------------------------------------------------------------
Message: 1
Date: Thu, 21 Mar 2019 11:13:21 -0700
From: "Tom Witt" <atwittsend@verizon.net>
To: <tigers@Autox.Team.Net>
Subject: Re: [Tigers] 66 MK 1A Wheel Alignment
I?d think the shop manual setting are all but erased these days. Tires are =
significantly different. Even driving expectations have changed. Sometimes =
setting are to reduce tire wear as the #1 priority. Sometimes the settings =
are for steering factors such as ease of turning (especially with non-power=
steering cars). And sometimes the settings are to compensate for design fl=
aws.=C2=A0 While it has been stated that the toe out setting Dale recommend=
s are for ?turn in? response I wonder (regardless of how minor) if those se=
tting also improve the horrible Ackerman the Tiger has.=C2=A0 My inclinatio=
n would be that every Tiger is somewhat different as are the expectations o=
f the driver. BTW, the heavier a driver you are the more it would seen a co=
mparable weight be in the driver seat when setting.
Crossmember distortion and bolt head contact seem to be limitation with Cas=
ter.=C2=A0 I?d think today zero should be the minimum for Camber but likely=
something negative. And as mentioned Toe on a stock Tiger rack can often b=
e between one of two positions, neither ideal. Lastly I always find it inte=
resting when Toe is give in inches (or millimeters). Really it is an angle.=
In inches the tire/wheel diameter (large/small) will affect the angle. And=
..., where is the measurement point? At the wheel? At the tread? I?ve seem =
a lot of people use a tape measure at the tread and they are measuring no w=
here near the center (largest portion of) the tire diameter.=C2=A0 So, toe =
in inches can be rather ambiguous.
For any ?Do It Your Self? types here is a toe gage I made out of a bed fram=
e. One end is adjustable both at the lower rail, and at the contact bolt fo=
r different tack widths. The vertical holes allow setting at (or close to) =
the spindle height. The other end is not width adjustable but is height adj=
ustable. The contact bolt is spring loaded so the gage can be moved around =
tire bulge and return to it previous setting. It is a comparative device an=
d given the small differences (typically 1/16 =3D .062) I use feeler gages.=
Measurement is at the outer edge of the rim and in most cases I?m shooting=
for zero anyway..., maybe a hair toe in.
The Camber gage is purpose built for the 14? wheels and body contours of my=
daily driver. The biggest problem is wind blowing the pendulum weight. Bot=
h the Toe and Camber gage cost me essentially nothing since I had the mater=
ials lying around.
From: Ron Fraser via Tigers=20
Sent: Thursday, March 21, 2019 8:49 AM
To: 'Joel Martin' ; tigers@Autox.Team.Net=20
Subject: Re: [Tigers] 66 MK 1A Wheel Alignment
Joel
=C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 The front alignment=
on the Tiger has always been a question mark to me.
First you have to read the Shop Manual carefully and understand the Rootes =
alignment procedure.
Look at Section F, pg. 4 & 5 ? the Rootes method ? fully laden car with gap=
gauges front and rear with 400 lbs. added weight at the front.
=20
Has anyone ever used the Rootes method to set the alignment then removed th=
e gap gauges and weight to see what the unladen alignment numbers look like=
?
=20
Second, the Shop Manual alignment numbers are for the fully laden suspensio=
n.
Castor Angle =3D 3 degrees 50 minutes positive that =3D 3.8 degrees positiv=
e
Camber Angle =3D 30 minutes positive, plus or minus 15 minutes
Toe-in =3D 1/8 inch
=20
The desired setup numbers I have written down for the street with radial ti=
re:
Castor =3D 3 to 4 degrees positive
Camber =3D ? to ? degree negative
Toe-in =3D 1/16 inch
There is no indication if this is laden or unladen or exactly where I found=
these numbers.
=20
Currently I?m not sure what my front alignment number are but I watch for u=
neven tire wear ? I have none.
I believe I have between 1 to 2 degrees negative camber and around 1/16 inc=
h toe-in.
=20
Ron Fraser
=20
=20
=20
From: Tigers <tigers-bounces@autox.team.net> On Behalf Of Joel Martin via T=
igers
Sent: Wednesday, March 20, 2019 6:09 PM
To: Tiger List Serve <tigers@autox.team.net>
Subject: [Tigers] 66 MK 1A Wheel Alignment
=20
Alignment Thoughts
Yes I am confused about which specs to take with me to the alignment shop.=
=C2=A0 Maybe the light bulb will go on with your help.=20
=20
Reported: We didn't pay inordinate attention to the factory specs when alig=
ning my Tiger last time, but went with numbers which were more conducive to=
performance. The set up has been:=20
=20
Caster, as much as you can find reasonably, 3.75~.=C2=A0 Put in FIRST
=20
Camber -1.25~.=20
=20
Toe 0-1/16 (kind of hard with the stock tie rod end set up, you either get =
0 or 1/8 in or out).=20
=20
These settings have worn tires evenly (yes, even with the camber), made the=
car very autocross and open track friendly, and provided good straight lin=
e stability.
=20
Dale Says to use:=C2=A0 USE THESE
=20
Caster:=C2=A0 3-4 degress=C2=A0 shims - put on no matter what but .1 or 06 =
or 1 of each?.=C2=A0 Positive or negative?
=20
Camber: ? neg=20
=20
Toe:=C2=A0 0 to 1/16 out
=20
Factory:
=20
=20
Castor:=C2=A0 3.5 Positive
=20
Camber: ? Plus or minus ? positive=20
=20
Toe In: 1/8? (3mm)
=20
Confusion:=C2=A0 SS shims .100? thick FS58 and .060? thick FS58M says they =
are for ?camber?.=C2=A0 Are there castor shims as well or did I not take go=
od notes?=C2=A0 15? wheels on 205 x 50 x15 tires ? used mainly on the stree=
t with 4 hour trips so need good straight line stability.
=20
---------------------------------------------------------------------------=
-----
_______________________________________________
tigers@autox.team.net
Archive: http://www.team.net/pipermail/tigers http://autox.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/atwittsend@verizo=
n.net
---
This email has been checked for viruses by AVG.
https://www.avg.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/tigers/attachments/20190321/b5afe24a/=
attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image[1].png
Type: image/png
Size: 517775 bytes
Desc: not available
URL: <http://autox.team.net/pipermail/tigers/attachments/20190321/b5afe24a/=
attachment.png>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image[3].png
Type: image/png
Size: 401906 bytes
Desc: not available
URL: <http://autox.team.net/pipermail/tigers/attachments/20190321/b5afe24a/=
attachment-0001.png>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image[8].png
Type: image/png
Size: 315699 bytes
Desc: not available
URL: <http://autox.team.net/pipermail/tigers/attachments/20190321/b5afe24a/=
attachment-0002.png>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image[5].png
Type: image/png
Size: 169808 bytes
Desc: not available
URL: <http://autox.team.net/pipermail/tigers/attachments/20190321/b5afe24a/=
attachment-0003.png>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.png
Type: image/png
Size: 55222 bytes
Desc: not available
URL: <http://autox.team.net/pipermail/tigers/attachments/20190321/b5afe24a/=
attachment-0004.png>
------------------------------
Subject: Digest Footer
_______________________________________________
Tigers mailing list
Tigers@autox.team.net
http://autox.team.net/mailman/listinfo/tigers
Archive: http://www.team.net/pipermail/tigers http://autox.team.net/archive
------------------------------
End of Tigers Digest, Vol 11, Issue 111
***************************************
------=_Part_9084117_1272885732.1553213597043
Content-Transfer-Encoding: quoted-printable
<font color=3D'black' size=3D'2' face=3D'arial'>just a couple comments abou=
t the wheel alignment current discussion...almost all auto manufactures hav=
e recommended weight applications for doing an alignment, you would have to=
look far and wide to find a shop that does it, that being said most experi=
enced techs can align the vehicle to perform well and obtain acceptable tir=
e wear..secondly I can't comment on toe out as it pertains to a Tiger, &nbs=
p;but I can tell you that in my experience with regular modern passenger ca=
rs today the toe out condition usually causes the car to not tract very wel=
l and it will dart from side to side with steering input, and if excessive =
will cause abnormal tire wear to the inside edge..specialty shops for perfo=
rmance modern cars probably will weight the car to the drivers average occu=
pancy of the car, I worked in a Porsche shop many years ago and we did it, =
but most of those cars had suspension mods for auto cross and track days...=
.today when I do my cars at the shop I sit in the drivers seat for for fina=
l settings..members out there could probably do that at your local tire sho=
p, just ask
<div><br>
<br>
<div style=3D"font-family:helvetica,arial;font-size:10pt;color:black">-----=
Original Message-----<br>
From: tigers-request <tigers-request@autox.team.net><br>
To: tigers <tigers@autox.team.net><br>
Sent: Thu, Mar 21, 2019 5:58 pm<br>
Subject: Tigers Digest, Vol 11, Issue 111<br>
<br>
<div dir=3D"ltr">Send Tigers mailing list submissions to<br>
</div>
<div dir=3D"ltr"> <a ymailto=3D"mailto:tigers@autox.team.=
net" rel=3D"noopener noreferrer" href=3D"mailto:tigers@autox.team.net";>tige=
rs@autox.team.net</a><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">To subscribe or unsubscribe via the World Wide Web, visit<=
br>
</div>
<div dir=3D"ltr"> <a target=3D"_blank" rel=3D"noopener no=
referrer" href=3D"http://autox.team.net/mailman/listinfo/tigers";>http://aut=
ox.team.net/mailman/listinfo/tigers</a><br>
</div>
<div dir=3D"ltr">or, via email, send a message with subject or body 'help' =
to<br>
</div>
<div dir=3D"ltr"> <a ymailto=3D"mailto:tigers-request@aut=
ox.team.net" rel=3D"noopener noreferrer" href=3D"mailto:tigers-request@auto=
x.team.net">tigers-request@autox.team.net</a><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">You can reach the person managing the list at<br>
</div>
<div dir=3D"ltr"> <a ymailto=3D"mailto:tigers-owner@autox=
.team.net" rel=3D"noopener noreferrer" href=3D"mailto:tigers-owner@autox.te=
am.net">tigers-owner@autox.team.net</a><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">When replying, please edit your Subject line so it is more=
specific<br>
</div>
<div dir=3D"ltr">than "Re: Contents of Tigers digest..."<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Today's Topics:<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> 1. Re: 66 MK 1A Wheel Alignment (Tom Witt)<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">----------------------------------------------------------=
------------<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Message: 1<br>
</div>
<div dir=3D"ltr">Date: Thu, 21 Mar 2019 11:13:21 -0700<br>
</div>
<div dir=3D"ltr">From: "Tom Witt" <<a ymailto=3D"mailto:atwittsend@veriz=
on.net" rel=3D"noopener noreferrer" href=3D"mailto:atwittsend@verizon.net";>=
atwittsend@verizon.net</a>><br>
</div>
<div dir=3D"ltr">To: <<a ymailto=3D"mailto:tigers@Autox.Team.Net"; rel=3D=
"noopener noreferrer" href=3D"mailto:tigers@Autox.Team.Net";>tigers@Autox.Te=
am.Net</a>><br>
</div>
<div dir=3D"ltr">Subject: Re: [Tigers] 66 MK 1A Wheel Alignment<br>
</div>
<div dir=3D"ltr">Message-ID: <<a ymailto=3D"mailto:5E52898FA1844B268CFB0=
2F6E9319DEE@user1PC" rel=3D"noopener noreferrer" href=3D"mailto:5E52898FA18=
44B268CFB02F6E9319DEE@user1PC">5E52898FA1844B268CFB02F6E9319DEE@user1PC</a>=
><br>
</div>
<div dir=3D"ltr">Content-Type: text/plain; charset=3D"utf-8"<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">I?d think the shop manual setting are all but erased these=
days. Tires are significantly different. Even driving expectations have ch=
anged. Sometimes setting are to reduce tire wear as the #1 priority. Someti=
mes the settings are for steering factors such as ease of turning (especial=
ly with non-power steering cars). And sometimes the settings are to compens=
ate for design flaws. While it has been stated that the toe out setti=
ng Dale recommends are for ?turn in? response I wonder (regardless of how m=
inor) if those setting also improve the horrible Ackerman the Tiger has.&nb=
sp; My inclination would be that every Tiger is somewhat different as are t=
he expectations of the driver. BTW, the heavier a driver you are the more i=
t would seen a comparable weight be in the driver seat when setting.<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Crossmember distortion and bolt head contact seem to be li=
mitation with Caster. I?d think today zero should be the minimum for =
Camber but likely something negative. And as mentioned Toe on a stock Tiger=
rack can often be between one of two positions, neither ideal. Lastly I al=
ways find it interesting when Toe is give in inches (or millimeters). Reall=
y it is an angle. In inches the tire/wheel diameter (large/small) will affe=
ct the angle. And..., where is the measurement point? At the wheel? At the =
tread? I?ve seem a lot of people use a tape measure at the tread and they a=
re measuring no where near the center (largest portion of) the tire diamete=
r. So, toe in inches can be rather ambiguous.<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">For any ?Do It Your Self? types here is a toe gage I made =
out of a bed frame. One end is adjustable both at the lower rail, and at th=
e contact bolt for different tack widths. The vertical holes allow setting =
at (or close to) the spindle height. The other end is not width adjustable =
but is height adjustable. The contact bolt is spring loaded so the gage can=
be moved around tire bulge and return to it previous setting. It is a comp=
arative device and given the small differences (typically 1/16 =3D .062) I =
use feeler gages. Measurement is at the outer edge of the rim and in most c=
ases I?m shooting for zero anyway..., maybe a hair toe in.<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">The Camber gage is purpose built for the 14? wheels and bo=
dy contours of my daily driver. The biggest problem is wind blowing the pen=
dulum weight. Both the Toe and Camber gage cost me essentially nothing sinc=
e I had the materials lying around.<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">From: Ron Fraser via Tigers <br>
</div>
<div dir=3D"ltr">Sent: Thursday, March 21, 2019 8:49 AM<br>
</div>
<div dir=3D"ltr">To: 'Joel Martin' ; <a ymailto=3D"mailto:tigers@Autox.Team=
.Net" rel=3D"noopener noreferrer" href=3D"mailto:tigers@Autox.Team.Net";>tig=
ers@Autox.Team.Net</a> <br>
</div>
<div dir=3D"ltr">Subject: Re: [Tigers] 66 MK 1A Wheel Alignment<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Joel<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> Th=
e front alignment on the Tiger has always been a question mark to me.<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">First you have to read the Shop Manual carefully and under=
stand the Rootes alignment procedure.<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Look at Section F, pg. 4 & 5 ? the Rootes method ? ful=
ly laden car with gap gauges front and rear with 400 lbs. added weight at t=
he front.<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Has anyone ever used the Rootes method to set the alignmen=
t then removed the gap gauges and weight to see what the unladen alignment =
numbers look like?<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Second, the Shop Manual alignment numbers are for the full=
y laden suspension.<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Castor Angle =3D 3 degrees 50 minutes positive that =3D 3.=
8 degrees positive<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Camber Angle =3D 30 minutes positive, plus or minus 15 min=
utes<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Toe-in =3D 1/8 inch<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">The desired setup numbers I have written down for the stre=
et with radial tire:<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Castor =3D 3 to 4 degrees positive<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Camber =3D ? to ? degree negative<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Toe-in =3D 1/16 inch<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">There is no indication if this is laden or unladen or exac=
tly where I found these numbers.<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Currently I?m not sure what my front alignment number are =
but I watch for uneven tire wear ? I have none.<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">I believe I have between 1 to 2 degrees negative camber an=
d around 1/16 inch toe-in.<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Ron Fraser<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">From: Tigers <<a ymailto=3D"mailto:tigers-bounces@autox=
.team.net" rel=3D"noopener noreferrer" href=3D"mailto:tigers-bounces@autox.=
team.net">tigers-bounces@autox.team.net</a>> On Behalf Of Joel Martin vi=
a Tigers<br>
</div>
<div dir=3D"ltr">Sent: Wednesday, March 20, 2019 6:09 PM<br>
</div>
<div dir=3D"ltr">To: Tiger List Serve <<a ymailto=3D"mailto:tigers@autox=
.team.net" rel=3D"noopener noreferrer" href=3D"mailto:tigers@autox.team.net=
">tigers@autox.team.net</a>><br>
</div>
<div dir=3D"ltr">Subject: [Tigers] 66 MK 1A Wheel Alignment<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Alignment Thoughts<br>
</div>
<div dir=3D"ltr">Yes I am confused about which specs to take with me to the=
alignment shop. Maybe the light bulb will go on with your help. <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Reported: We didn't pay inordinate attention to the factor=
y specs when aligning my Tiger last time, but went with numbers which were =
more conducive to performance. The set up has been: <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Caster, as much as you can find reasonably, 3.75~. P=
ut in FIRST<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Camber -1.25~. <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Toe 0-1/16 (kind of hard with the stock tie rod end set up=
, you either get 0 or 1/8 in or out). <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">These settings have worn tires evenly (yes, even with the =
camber), made the car very autocross and open track friendly, and provided =
good straight line stability.<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Dale Says to use: USE THESE<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Caster: 3-4 degress shims - put on no matter =
what but .1 or 06 or 1 of each?. Positive or negative?<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Camber: ? neg <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Toe: 0 to 1/16 out<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Factory:<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Castor: 3.5 Positive<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Camber: ? Plus or minus ? positive <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Toe In: 1/8? (3mm)<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Confusion: SS shims .100? thick FS58 and .060? thick=
FS58M says they are for ?camber?. Are there castor shims as well or =
did I not take good notes? 15? wheels on 205 x 50 x15 tires ? used ma=
inly on the street with 4 hour trips so need good straight line stability.<=
br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"> <br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">----------------------------------------------------------=
----------------------<br>
</div>
<div dir=3D"ltr">_______________________________________________<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"><a ymailto=3D"mailto:tigers@autox.team.net"; rel=3D"noopene=
r noreferrer" href=3D"mailto:tigers@autox.team.net";>tigers@autox.team.net</=
a><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Donate: <a target=3D"_blank" rel=3D"noopener noreferrer" h=
ref=3D"http://www.team.net/donate.html";>http://www.team.net/donate.html</a>=
<br>
</div>
<div dir=3D"ltr">Archive: <a target=3D"_blank" rel=3D"noopener noreferrer" =
href=3D"http://www.team.net/pipermail/tigers";>http://www.team.net/pipermail=
/tigers </a><a target=3D"_blank" rel=3D"noopener noreferrer" href=3D"http:/=
/autox.team.net/archive">http://autox.team.net/archive</a><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Unsubscribe: <a target=3D"_blank" rel=3D"noopener noreferr=
er" href=3D"http://autox.team.net/mailman/options/tigers/atwittsend@verizon=
.net">http://autox.team.net/mailman/options/tigers/atwittsend@verizon.net</=
a><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">---<br>
</div>
<div dir=3D"ltr">This email has been checked for viruses by AVG.<br>
</div>
<div dir=3D"ltr"><a target=3D"_blank" rel=3D"noopener noreferrer" href=3D"h=
ttps://www.avg.com">https://www.avg.com</a><br>
</div>
<div dir=3D"ltr">-------------- next part --------------<br>
</div>
<div dir=3D"ltr">An HTML attachment was scrubbed...<br>
</div>
<div dir=3D"ltr">URL: <<a target=3D"_blank" rel=3D"noopener noreferrer" =
href=3D"http://autox.team.net/pipermail/tigers/attachments/20190321/b5afe24=
a/attachment.html">http://autox.team.net/pipermail/tigers/attachments/20190=
321/b5afe24a/attachment.html</a>><br>
</div>
<div dir=3D"ltr">-------------- next part --------------<br>
</div>
<div dir=3D"ltr">A non-text attachment was scrubbed...<br>
</div>
<div dir=3D"ltr">Name: image[1].png<br>
</div>
<div dir=3D"ltr">Type: image/png<br>
</div>
<div dir=3D"ltr">Size: 517775 bytes<br>
</div>
<div dir=3D"ltr">Desc: not available<br>
</div>
<div dir=3D"ltr">URL: <<a target=3D"_blank" rel=3D"noopener noreferrer" =
href=3D"http://autox.team.net/pipermail/tigers/attachments/20190321/b5afe24=
a/attachment.png">http://autox.team.net/pipermail/tigers/attachments/201903=
21/b5afe24a/attachment.png</a>><br>
</div>
<div dir=3D"ltr">-------------- next part --------------<br>
</div>
<div dir=3D"ltr">A non-text attachment was scrubbed...<br>
</div>
<div dir=3D"ltr">Name: image[3].png<br>
</div>
<div dir=3D"ltr">Type: image/png<br>
</div>
<div dir=3D"ltr">Size: 401906 bytes<br>
</div>
<div dir=3D"ltr">Desc: not available<br>
</div>
<div dir=3D"ltr">URL: <<a target=3D"_blank" rel=3D"noopener noreferrer" =
href=3D"http://autox.team.net/pipermail/tigers/attachments/20190321/b5afe24=
a/attachment-0001.png">http://autox.team.net/pipermail/tigers/attachments/2=
0190321/b5afe24a/attachment-0001.png</a>><br>
</div>
<div dir=3D"ltr">-------------- next part --------------<br>
</div>
<div dir=3D"ltr">A non-text attachment was scrubbed...<br>
</div>
<div dir=3D"ltr">Name: image[8].png<br>
</div>
<div dir=3D"ltr">Type: image/png<br>
</div>
<div dir=3D"ltr">Size: 315699 bytes<br>
</div>
<div dir=3D"ltr">Desc: not available<br>
</div>
<div dir=3D"ltr">URL: <<a target=3D"_blank" rel=3D"noopener noreferrer" =
href=3D"http://autox.team.net/pipermail/tigers/attachments/20190321/b5afe24=
a/attachment-0002.png">http://autox.team.net/pipermail/tigers/attachments/2=
0190321/b5afe24a/attachment-0002.png</a>><br>
</div>
<div dir=3D"ltr">-------------- next part --------------<br>
</div>
<div dir=3D"ltr">A non-text attachment was scrubbed...<br>
</div>
<div dir=3D"ltr">Name: image[5].png<br>
</div>
<div dir=3D"ltr">Type: image/png<br>
</div>
<div dir=3D"ltr">Size: 169808 bytes<br>
</div>
<div dir=3D"ltr">Desc: not available<br>
</div>
<div dir=3D"ltr">URL: <<a target=3D"_blank" rel=3D"noopener noreferrer" =
href=3D"http://autox.team.net/pipermail/tigers/attachments/20190321/b5afe24=
a/attachment-0003.png">http://autox.team.net/pipermail/tigers/attachments/2=
0190321/b5afe24a/attachment-0003.png</a>><br>
</div>
<div dir=3D"ltr">-------------- next part --------------<br>
</div>
<div dir=3D"ltr">A non-text attachment was scrubbed...<br>
</div>
<div dir=3D"ltr">Name: image001.png<br>
</div>
<div dir=3D"ltr">Type: image/png<br>
</div>
<div dir=3D"ltr">Size: 55222 bytes<br>
</div>
<div dir=3D"ltr">Desc: not available<br>
</div>
<div dir=3D"ltr">URL: <<a target=3D"_blank" rel=3D"noopener noreferrer" =
href=3D"http://autox.team.net/pipermail/tigers/attachments/20190321/b5afe24=
a/attachment-0004.png">http://autox.team.net/pipermail/tigers/attachments/2=
0190321/b5afe24a/attachment-0004.png</a>><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">------------------------------<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Subject: Digest Footer<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">_______________________________________________<br>
</div>
<div dir=3D"ltr">Tigers mailing list<br>
</div>
<div dir=3D"ltr"><a ymailto=3D"mailto:Tigers@autox.team.net"; rel=3D"noopene=
r noreferrer" href=3D"mailto:Tigers@autox.team.net";>Tigers@autox.team.net</=
a><br>
</div>
<div dir=3D"ltr"><a target=3D"_blank" rel=3D"noopener noreferrer" href=3D"h=
ttp://autox.team.net/mailman/listinfo/tigers">http://autox.team.net/mailman=
/listinfo/tigers</a><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">Donate: <a target=3D"_blank" rel=3D"noopener noreferrer" h=
ref=3D"http://www.team.net/donate.html";>http://www.team.net/donate.html</a>=
<br>
</div>
<div dir=3D"ltr">Archive: <a target=3D"_blank" rel=3D"noopener noreferrer" =
href=3D"http://www.team.net/pipermail/tigers";>http://www.team.net/pipermail=
/tigers </a><a target=3D"_blank" rel=3D"noopener noreferrer" href=3D"http:/=
/autox.team.net/archive">http://autox.team.net/archive</a><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">------------------------------<br>
</div>
<div dir=3D"ltr"><br>
</div>
<div dir=3D"ltr">End of Tigers Digest, Vol 11, Issue 111<br>
</div>
<div dir=3D"ltr">***************************************<br>
</div>
</div>
</div>
</font>
------=_Part_9084117_1272885732.1553213597043--
--===============6699595329822386823==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
tigers@autox.team.net
Archive: http://www.team.net/pipermail/tigers http://autox.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/mharc@autox.team.net
--===============6699595329822386823==--
|