triumphs
[Top] [All Lists]

Cooling System Mystery - please help

To: triumphs@Autox.Team.Net, spitfires@Autox.Team.Net
Subject: Cooling System Mystery - please help
Date: Fri, 31 Dec 2004 20:29:03 +0000
User-agent: Turnpike/6.04-U (<bsFwmuFTLMJQ89Zo4lpFuLp2+u>)
Dear All,

I've been very quiet of late, since all the things that have gone wrong 
with my cars over the past few months have been things that I have been 
able to diagnose and fix myself.   This is no longer the case.   I would 
be grateful for any suggestions that you guys might be able to come up 
with - I'm stumped...

Symptoms
I drove Carly (the Spit) up to London yesterday, with the heater on, and 
just as I neared my destination, the heater started blowing cold air, 
and the engine temperature began to rise - fast.   Normally, the 
temperature gauge in my car reads about 1/4, but it rapidly went up to 
3/4.   I parked up, and came back to the car a few hours later.   I 
checked the coolant level (a trifle low, but I was able to top up using 
considerably less than a pint of water), and consistency (watery - no 
sign of emulsification).   I checked the oil (oil-coloured, and correct 
fill level).   I then drove for about two miles at 40 mph, by which time 
the temperature gauge was over the 3/4 mark.   The top of the radiator 
was too hot to touch, but the main body of the rad, and most of the 
hoses, were cold.   I fiddled about sticking screwdriver blades up the 
hoses at the side of the road, trying to see if there was a blockage I 
could clear, and eventually decided to remove the thermostat.   Having 
done this, I was able to drive the 70 miles home at 60 mph with the 
temperature gauge reading 1/2.

Treatment
Today, I flushed the cooling system with cold water at mains pressure 
(in both directions, and using as many orifices as I could, including 
the heater hoses); I checked the fan belt tension (which was correct) - 
it is rotating correctly in any case; I removed the water pump and found 
it to be in as-new condition and rotating freely (so I put it back on 
the car, with a new gasket); I tested the 'stat, and found that it was 
opening and closing correctly at 73 degrees (so I put it back on the 
car, with a new gasket); I removed the heater control valve, and pulled 
out several bits of orange rubbery stuff (the remains of some DPO's 
Instant Gasket which was used on the water pump housing).   I then 
refitted the valve.   Next I drove the car around the block.   Still no 
heat from the heater.   Engine temperature still rising to 3/4 on the 
gauge.   Radiator now getting warm on the inlet side, and all hoses 
except heater hoses getting warm too.   Additionally, and unfortunately, 
there is now a hole in the radiator, through which coolant is spraying 
onto the fan.   This was not the case before.   Either I punctured the 
rad getting the water pump and fan assembly off, or the water pressure 
in the system has punched its own hole.

I don't want to buy and fit a new radiator, only to have the first 
problem blow a hole through that as well, but I cannot work out what 
that problem can be.   It must be a blockage somewhere in the system, 
I'm sure, but flushing shows that water flows right the way through the 
system without any trouble.   Can you help?   Please?

Thanks in advance for anything you can suggest.

ATB
-- 
Mike
Ellie  - 1963 White Herald 1200 Convertible GA125624 CV
Connie - 1968 Conifer Herald 1200 Saloon GA237511 DL
Carly  - 1977 Inca Yellow Spitfire 1500 FH105671




<Prev in Thread] Current Thread [Next in Thread>