triumphs
[Top] [All Lists]

[TR] Headlights/driving lights/relays/fuses/connectors

Subject: [TR] Headlights/driving lights/relays/fuses/connectors
From: spamiam at comcast.net (spamiam at comcast.net)
Date: Sat, 9 Apr 2011 08:44:08 -0400
References: <03d301cbf3a2$324fc050$0301a8c0@randall> <1005208835.585081.1302025311427.JavaMail.root@sz0135a.westchester.pa.mail.comcast.net> <01d001cbf3d8$14305b30$3c911190$@rr.com>
All,

A couple of ideas/questions:


1)  I did some more thinking about the conundrum of my old original 
headlights being "inadequate", and the fact that I have a couple pairs of 
driving lights on a shelf, and the fact that my generator for my TR4A is 
only good for 22 amps.  I don't have enough generator capacity to keep up 
with two 55W headlights, and two 55W driving lights, as well as running 
lights, ignition, and occasionally a heater fan.  55 Watts = 4.6 Amps  Four 
bulbs simultaneously = 18.3A with 3.7 amps left over

Sensible people here on the forum suggested that I get some good modern H4 
headlights.  I got some from BUSDEPOT.COM.  They have arrived.  They are 
labeled "motorcycle" on the glass, but I presume they will be fine for 
automobile use as well.  I got the 60/55 bulbs to go with them.  I have some 
new 100/55 bulbs intended for a long gone car, but never used.  I was 
thinking that I could use a 100/55 bulb in ONE of the lights, almost like 
what they did on the old days with having ONE driving light (and one fog 
light) (I never understood why they used ONE until I thought of the power 
limitations, a 22A generator can only power one extra 55W bulb without 
brown-out).

What do you think about  using one 100W high beam and one 60W high beam 
bulb?  I doubt I will actually do it, and it is a pain in the neck to pull 
the leadlight out of the bucket to change the bulb just to test 100W on one 
side....


2)  I will upgrade the wiring to properly supply the new lights.  I want to 
have the upgrade as invisible as possible for concours shows, but I want the 
relays (and fuses?) to be reasonably easily accessible.  I think it makes 
good sense to have the relays near the headlights, rather than under the 
dash so that there are short runs from the relays to the bulbs.  So... 
where should I put them?  Randall put them under on the bottom of a 
headlight bucket, and that is well hidden, but not too accessible. 
Suggestions?


3) To fuse or not to fuse.  Right now I am thinking that I will put type I 
auto-resetting circuit breakers piggybacked to the relays.  One breaker for 
both high beams, and a separate one for both low beams.  This protects only 
the relatively short runs from the relays to the bulbs.  The big hot wire 
coming from the voltage regulator A1 terminal won't be fused.  Due to its 
length and location, I'd guess that one is at more risk of shorting.  But I 
REALLY REALLY don't want to put any sort of fuse on the single main power 
supply to all the forward facing lights!  Maybe a BIG fusible link. 
Something like 50A.  If I were to draw 50A long enough to blow the fusible 
link, then I had a serious problem, and I was going to lose the lights 
anyway.  Suggestions?


4)  What connectors should I use when I need to branch a single wire to two 
wires.  The original harness uses bullet terminals and 4-way connectors to 
go to the high and low filaments.  These have always seemed to me to be 
prone to corrosion and bad connections.  But the new connectors from British 
Wiring are stainless steel, so I suppose they are less prone to corrosion. 
Should I pack them with dielectric grease to seal them from the elements? 
If I use bullet terminals, should I solder or crimp, or both?  It would be a 
bit of a waste of money to buy a $50+ crimper if I am going to solder 
anyway, but I like a GOOD crimped connection.


5)  How is the ground connected for the headlights on the 4A?  I haven't 
looked hard at the stock wiring to see how the ground is handled.  Do the 
two grounds from the bulbs meet at a bullet connector,and then where does it 
go after that to get to a good ground?

-Tony 


<Prev in Thread] Current Thread [Next in Thread>