This is a multipart message in MIME format.
--===============2055318680730181397==
boundary="----=_NextPart_000_070D_01D5A83B.02C88450"
Content-Language: en-ca
This is a multipart message in MIME format.
------=_NextPart_000_070D_01D5A83B.02C88450
charset="us-ascii"
Content-Transfer-Encoding: 7bit
Anyone install the rubber seal between the Factory backlight and the body on
a TR4/4A/5/250? The TRF seal has a "U" channel on each surface. One of these
is larger than the other. The larger channel is a perfect fit for the
backlight but it would seem almost impossible to get the narrower seal to
spread out over the rear deck. The narrower surface would seem quite a
challenge to glue it to the underside of the back light. Any ideas?
Thanks
Keith
Keith Stewart
keithstewart@bell.net
------=_NextPart_000_070D_01D5A83B.02C88450
charset="us-ascii"
Content-Transfer-Encoding: quoted-printable
<html xmlns:v=3D"urn:schemas-microsoft-com:vml" =
xmlns:o=3D"urn:schemas-microsoft-com:office:office" =
xmlns:w=3D"urn:schemas-microsoft-com:office:word" =
xmlns:m=3D"http://schemas.microsoft.com/office/2004/12/omml"; =
xmlns=3D"http://www.w3.org/TR/REC-html40";><head><META =
HTTP-EQUIV=3D"Content-Type" CONTENT=3D"text/html; =
charset=3Dus-ascii"><meta name=3DGenerator content=3D"Microsoft Word 15 =
(filtered medium)"><style><!--
/* Font Definitions */
@font-face
{font-family:"Cambria Math";
panose-1:2 4 5 3 5 4 6 3 2 4;}
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:11.0pt;
font-family:"Calibri",sans-serif;
mso-fareast-language:EN-US;}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:#0563C1;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{mso-style-priority:99;
color:#954F72;
text-decoration:underline;}
span.EmailStyle17
{mso-style-type:personal-compose;
font-family:"Calibri",sans-serif;
color:windowtext;}
.MsoChpDefault
{mso-style-type:export-only;
font-family:"Calibri",sans-serif;
mso-fareast-language:EN-US;}
@page WordSection1
{size:8.5in 11.0in;
margin:1.0in 1.0in 1.0in 1.0in;}
div.WordSection1
{page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext=3D"edit" spidmax=3D"1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext=3D"edit">
<o:idmap v:ext=3D"edit" data=3D"1" />
</o:shapelayout></xml><![endif]--></head><body lang=3DEN-CA =
link=3D"#0563C1" vlink=3D"#954F72"><div class=3DWordSection1><p =
class=3DMsoNormal>Anyone install the rubber seal between the Factory =
backlight and the body on a TR4/4A/5/250? The TRF seal has a =
“U” channel on each surface. One of these is larger than the =
other. The larger channel is a perfect fit for the backlight but it =
would seem almost impossible to get the narrower seal to spread out over =
the rear deck. The narrower surface would seem quite a challenge to glue =
it to the underside of the back light. Any ideas?<o:p></o:p></p><p =
class=3DMsoNormal><o:p> </o:p></p><p =
class=3DMsoNormal>Thanks<o:p></o:p></p><p =
class=3DMsoNormal>Keith<o:p></o:p></p><p =
class=3DMsoNormal><o:p> </o:p></p><p class=3DMsoNormal><span =
style=3D'mso-fareast-language:EN-CA'>Keith =
Stewart<o:p></o:p></span></p><p class=3DMsoNormal><span =
style=3D'mso-fareast-language:EN-CA'>keithstewart@bell.net<o:p></o:p></sp=
an></p><p class=3DMsoNormal><o:p> </o:p></p></div></body></html>
------=_NextPart_000_070D_01D5A83B.02C88450--
--===============2055318680730181397==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
** triumphs@autox.team.net **
Archive: http://www.team.net/pipermail/triumphs http://www.team.net/archive
--===============2055318680730181397==--
|