[Fot] Peugot lifters 504

[gt6steve at aol.com]

Please take this with a grain of salt but I recall the lifter bores to be at 5 degrees off vertical.  Measured a long time ago so if someone can verify that it would be safer for all LOL




-----Original Message-----
From: Mike Harmuth via Fot <fot at autox.team.net>
To: FoTTriumph <fot at autox.team.net>
Sent: Thu, Nov 16, 2017 8:18 am
Subject: Re: [Fot] Peugot lifters 504




"And they've been used in at least one 1296 Spitfire engine, where they're much larger in diameter than stock."


Now you have my interest, I have a small block 1296 block with worn lifter bores and my engine builder couldn't find a slightly larger lifter. I'm guessing he didn't look at a Peugeot parts catalog. Does anyone have a lifter part number or a spec so I can investigate bringing this block back from the dead? It was mentioned that the TR bores holes are not parallel to the block, are the small journal 1296 bore the same?


thanks

mike h



On Wed, Nov 15, 2017 at 4:44 PM, Mordy Dunst via Fot <fot at autox.team.net> wrote:

These stock lifters are larger diameter than triumph. Why would anyone look for large diameter lifters?

MDunst Headgasket.com 626.358.1616
Fax 626.628.3777
Triple R Munitions, Inc 626.201.9471
T FFL 6,7 SOT 2

On Wednesday, November 15, 2017, Barr, Scott via Fot <fot at autox.team.net> wrote:

And they've been used in at least one 1296 Spitfire engine, where they're much larger in diameter than stock.

Scott (B.)

-----Original Message-----
From: Fot [mailto:fot-bounces at autox.team.net] On Behalf Of Tony Drews via Fot
Sent: Tuesday, November 14, 2017 7:59 PM
To: Chuck Arnold and/or Kathleen Kelley <triosan at gmail.com>; Friends <fot at autox.team.net>
Subject: Re: [Fot] "GT40" lifters

They are commonly used in the TR-2/3/4 block in place of stock lifters by using a sleeve - in this case they are smaller than stock. If you use the cam developed by Larry Young you can't use those lifters as he needs the full diameter of the stock lifter. The Elgin cams work OK with them though.

I'd not heard of using them in a TR-6 until now though.

Regards, Tony

At 01:02 PM 11/14/2017, Chuck Arnold and/or Kathleen Kelley via Fot wrote:
>Somewhere in a Triumph post I read about using what I think were
>referred to as GT40 liofters [tappets]. They are slightly larger in
>diameter than stock TR6 ones. A set came with my car, but have never
>been used. Does anyone know of there and the modification [or where I
>might have read about them?]. Also, they are for sale.
>
>Thanks,
>
>Chuck
>_______________________________________________
>fot at autox.team.net
>
>http://www.fot-racing.com
>
>Donate: http://www.team.net/donate.html
>Archive: http://www.team.net/archive
>Forums: http://www.team.net/forums
>Unsubscribe/Manage:
>http://autox.team.net/mailman/options/fot/tony@tonydrews.com


_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/sbarr@mccarty-law.com


_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/gasket.works@gte.net



_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/ofracer@gmail.com






_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/gt6steve@aol.com



-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/fot/attachments/20171116/b1b7d370/attachment-0001.htm>