[Fot] Fwd: TR6 inner shaft bearing

Tue Apr 14 06:40:21 MDT 2020

Hi Glen, 
that is explaining the issue. It seems that lot's of these bearings have been replaced in that way by now! 
Marcel 

Van: "fot" <fot at autox.team.net> 
Aan: "fot" <fot at autox.team.net> 
Verzonden: Dinsdag 14 april 2020 13:56:06 
Onderwerp: Re: [Fot] Fwd: TR6 inner shaft bearing 

There's a slight step on the shaft that prevents inward movement of the bearing, relative to the shaft; if your shaft slid out, that step has been removed. 
I've run into this several times, it's done in a last-ditch effort to change the bearing when the hub can't be removed. 
Glen 
Note... I'm not advocating this as a correct repair procedure 

-----Original Message----- 
From: van.mulders.marcel--- via Fot <fot at autox.team.net> 
To: fot <fot at autox.team.net> 
Sent: Tue, Apr 14, 2020 5:48 am 
Subject: [Fot] Fwd: TR6 inner shaft bearing 

Van: "van mulders marcel" <van.mulders.marcel at telenet.be> 
Aan: "Chip Collingwood" <chip at theukmotorsports.com> 
Verzonden: Dinsdag 14 april 2020 09:18:41 
Onderwerp: Re: [Fot] TR6 inner shaft bearing 

I discovered a couple of times that the bearing did move on the shaft by as much as 1/2". As a result the shaft had moved outwards by that amount. Is that common? Is there a simple fix? 
Marcel 
Aan: "Jay Galbreath" <tr4jay at gmail.com> 
Cc: "fot" <fot at autox.team.net> 
Verzonden: Zondag 12 april 2020 01:55:19 
Onderwerp: Re: [Fot] TR6 inner shaft bearing 

the flange fits on a tapered shaft which is the bear...the bearing doesn't take much at all...if you do happen to find a shop that can get it apart for you make sure you make a note of the bearing position on the shaft...take a measurement before you press it off for reference. I use a 50 ton press to get the flange apart...usually takes at least 20 tons...sometimes more...always wrap a towel around the assembly...dont think I've ever had one i couldn't get apart. 

On Sat, Apr 11, 2020, 7:49 PM Jay Galbreath via Fot < [ mailto:fot at autox.team.net | fot at autox.team.net ] > wrote: 

Hah! I just attempted that this week. The two stub shafts would NOT press out even with 10 tons and red hot from my firewrench. Scott Harper at Team Triumph came to my rescue and went through his stash to find a couple that did press out for him. So give him a call if you can't break them apart. Good Luck! Jay WPTA 

On Sat, Apr 11, 2020 at 6:22 PM Michael Deweerd via Fot < [ mailto:fot at autox.team.net | fot at autox.team.net ] > wrote: 

BQ_BEGIN

Amici 
How much force is typically required to separate the driving flange from the shaft 

-- 
Mike Deweerd 
_______________________________________________ 
[ mailto:fot at autox.team.net | fot at autox.team.net ] 

[ http://www.fot-racing.com/ | http://www.fot-racing.com ] 

Donate: [ http://www.team.net/donate.html | http://www.team.net/donate.html ] 
Archive: [ http://autox.team.net/archive | http://autox.team.net/archive ] [ http://www.team.net/pipermail/fotUnsubscribe/Manage | http://www.team.net/pipermail/fot

Unsubscribe/Manage ] : [ http://autox.team.net/mailman/options/fot/tr4jay@gmail.com | http://autox.team.net/mailman/options/fot/tr4jay@gmail.com ] 

_______________________________________________ 
[ mailto:fot at autox.team.net | fot at autox.team.net ] 

[ http://www.fot-racing.com/ | http://www.fot-racing.com ] 

Donate: [ http://www.team.net/donate.html | http://www.team.net/donate.html ] 
Archive: [ http://autox.team.net/archive | http://autox.team.net/archive ] [ http://www.team.net/pipermail/fotUnsubscribe/Manage | http://www.team.net/pipermail/fot

Unsubscribe/Manage ] : [ http://autox.team.net/mailman/options/fot/chip@theukmotorsports.com | http://autox.team.net/mailman/options/fot/chip@theukmotorsports.com ] 

BQ_END

_______________________________________________ 
fot at autox.team.net 

http://www.fot-racing.com 

Donate: http://www.team.net/donate.html 
Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot 
Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/van.mulders.marcel@telenet.be 

_______________________________________________ 
[ mailto:fot at autox.team.net | fot at autox.team.net ] 

[ http://www.fot-racing.com/ | http://www.fot-racing.com ] 

Donate: [ http://www.team.net/donate.html | http://www.team.net/donate.html ] 
Archive: [ http://autox.team.net/archive | http://autox.team.net/archive  ] [ http://www.team.net/pipermail/fot | http://www.team.net/pipermail/fot ] 
Unsubscribe/Manage: [ http://autox.team.net/mailman/options/fot/fubog1@aol.com | http://autox.team.net/mailman/options/fot/fubog1@aol.com ] 

_______________________________________________ 
fot at autox.team.net 

http://www.fot-racing.com 

Donate: http://www.team.net/donate.html 
Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot 
Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/van.mulders.marcel@telenet.be 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/fot/attachments/20200414/1c2cda1f/attachment-0003.htm>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: 60833538733__170635DE-43AC-436F-9B31-D1CB800D472A.jpeg
Type: image/jpeg
Size: 2574955 bytes
Desc: not available
URL: <http://autox.team.net/pipermail/fot/attachments/20200414/1c2cda1f/attachment-0003.jpeg>