[Fot] Differential Pre-load

barry rosenberg britcars at bellsouth.net
Wed Jan 29 11:02:55 MST 2020


 Preload is more for the life of the bearings than the gears. You preload a bearing to take up manufacturing tolerances and account for the anticipated (by the manufacturer of the bearings) wear during their life time. There does need to be some 'squeeze" between the bearing races and the rollers or the rollers will not roll in lubrication. If any of you have ever rebuilt the rear outer suspension on old XKEs, the tapers roller bearing in the outer wishbone pivots wear out because the wishbone only moves up and down a few degrees. The tapered roller bearings never fully rotate and cause the rollers and race to pit. Roller bearing must roll 360 degrees around to survive. Preload makes them do that.
Barry
    On Wednesday, January 29, 2020, 09:41:34 AM EST, Bob Kramer via Fot <fot at autox.team.net> wrote:  
 
 I think the main reason a specified amount of  preload is required is that it sets it up so that the bearings roll under mild tension. To tight and the components slide over each other.  Too loose and they cock in place. Without rolling, bearings will soon fail the same way a lifter that doesn't spin fails.
Bob Kramer

On Wed, Jan 29, 2020 at 8:15 AM fubog1 via Fot <fot at autox.team.net> wrote:

 

Does someone know why that preload is necessary? 
 Yes it's basically because things want to move around a lot & the pinion wants to stretch.with torque on/off loads.Over time as the bearings wear, the preload will be lost, and any further wear will cause the gears to be out of mesh and the pattern will be lost and then they'll wear.Glen

 
-----Original Message-----
From: van.mulders.marcel--- via Fot <fot at autox.team.net>
To: Bill Tobin <william.tobin31 at verizon.net>
Cc: fot <fot at autox.team.net>
Sent: Wed, Jan 29, 2020 8:14 am
Subject: Re: [Fot] Differential Pre-load

Does someone know why that preload is necessary? When I check a differential before using it and I notice there is almost no preload at all, I tend to be lazy, assuming no preload means less friction loss.Marcel.
Van: "fot" <fot at autox.team.net>
Aan: "fot" <fot at autox.team.net>
Verzonden: Woensdag 29 januari 2020 04:06:57
Onderwerp: Re: [Fot] Differential Pre-load

Hi Scott I think that's the torque required to turn the pinion. Put a socket to fit the pinion nut on a?? inch pound torque wrench; measure how much torque it takes to turn the pinion. Get it turning and read the torque wrench while turning it. 12 to 15 inch pounds sounds ok. With shims either add or remove shims to get the correct preload. Thicker to lessen and thinner to increase I think. With a collapsible spacer it's easier. Keep?? tightening the nut and measuring the preload until it's right. Small increments. If you over tighten you take it apart and start over with a new spacer. (Ask me how I know this!) Also a "clicker" torque wrench isn't the ticket for this. Use an older beam type.
  Hope this helps. Cheers Bill
  On 1/28/2020 4:34 PM, Scott Janzen via Fot wrote:
  
 I???m rebuilding my differential. ??The manual says the pinion bearings should be assembled with spacers to yield a?? 12-16 lb/inch pre-load, using a bar affixed to the input flange and a sliding weight. ??Of course there is a churchhill tool for that! 
  Either I???m not grasping the concept, or 12 lbs per inch doesn???t seem right. ??I???m guessing this is supposed to be 12 inch-pounds, which I think means a one pound weight at the end of a 12??? lever. ??All testing is performed with the seal removed. 
  Even if I am correct, I???ve got it set up with about a 1/2 lb pre-load right now, and that feels pretty stiff already. 
  Anyone have any experience with this? ??This is a GT6 diff, but I???m guessing the instructions don???t vary much. 
  Thanks, Scott 
  _______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/william.tobin31@verizon.net


 
 
_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/van.mulders.marcel@telenet.be
_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/fubog1@aol.com


_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/rkramer56@gmail.com



_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/britcars@bellsouth.net


  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/fot/attachments/20200129/dd0776c6/attachment-0003.htm>


More information about the Fot mailing list