[Fot] Shop Safety Question

[Phil Gott]

Good advice, all of it.
In addition to a large extinguisher near each exit door I have an open 5 gallon bucket filled 2/3 with water. Great for dousing fires and for dunking/tempering hot pieces off the grinding wheel. Faster response than a hose or even an extinguisher. Used it when I set the grass affire outside my barn while grinding on my trailer. Yikes!
Phil

Sent from my iPhone

> On Jan 16, 2021, at 6:42 PM, Bob Bownes -Seiri via Fot <fot at autox.team.net> wrote:
> 
> 
> 
> Sounds a bit silly, but a broom.  
> 
> Keeping the floor clean cuts down on slips and trips, which OSHA says are some of the most common causes of liability claims. 
> 
> Bi-focal safety glasses for those of us over a certain age. Keeps you from taking them off to see better. 
> 
> The usual assortment of fire extinguishers of course. 
> 
> And a phone to call for help. :)
> 
> 
> 
>>> On Jan 16, 2021, at 15:38, Jason Sukey via Fot <fot at autox.team.net> wrote:
>>> 
>> 
>> Paul, 
>> Beyond the "minimum code requirement" extinguisher's that get inspected and tagged annually, I also keep a 2.5 gallon pressurized AFFF extinguisher and a 2.5 gallon water extinguisher charged and ready at my shop.
>> 
>> The township fire inspector recommend the AFFF for fuel and oil type fires, and he also stated it can be used to pre-treat a fuel spill while you clean it up to reduce the chances of a fire starting. 
>> 
>> He also recommended the water extinguisher near my welding area to knock down small flare ups.
>> 
>> I also make it a point to never leave until any welding or grinding work has cooled completely.
>> 
>> I also disconnect the battery in vehicles during storage.
>> 
>> 
>> When draining or filling a fuel tank, I roll the vehicle outside if possible.
>> 
>> Thankfully, I've never had a chance to test any of these items!
>> 
>> Jason
>> 
>>> On Sat, Jan 16, 2021, 1:32 PM Paul Ricco via Fot <fot at autox.team.net> wrote:
>>> FOT,
>>> 
>>> I have been lucky to work in some very well run industrial environments with world class safety equipment.  As we know, the stuff costs money and a lot of people work without most of it in their own environments.
>>> 
>>> We have been updating a lot of items in the areas that we work on car and car parts.  It is fun to spend money on tools and equipment.  However, safety equipment is not always as fun.  Near where we live, two pretty smart people have had fires damage their garages and parts of their houses before the fire department could arrive.  While I was running large car dealerships and body shops, I can tell you that fire extinguishers did need to be used from time to time.  Fortunately we had them and never needed to make a call to the fire department, because the right things were in the right places.
>>> 
>>> Therefore, we just upgraded all of our safety equipment.  Including:
>>> 
>>> 1.  Splatter/spark screens for areas that we weld or grind
>>> 2.  High quality US made fire extinguishers with plenty of capacity, including mounting them in the the trailer for at the track.  Some fires can be spread really quickly by hitting the with H20.  Generally speaking water will not put out burning oil fire.  However, it will spread the burning oil all over really quickly.
>>> 3.  Spark resistant blankets for use when we are welding in areas that things should be covered
>>> 4.  Making sure all flammables are stored safely and away from areas that could have sparks
>>> 5.  New and updated smoke detectors, heat sensors and Carbon Monoxide monitors where they can be used (not where we tune engines)
>>> 
>>> Obviously common sense can prevent a lot of accidents.  Therefore, I though it would be interesting to see what the group has done in their work areas.
>>> 
>>> Does anyone have anything else that keep around that they feel is helpful for shop area/garage safety?
>>> 
>>> Paul Ricco
>>> _______________________________________________
>>> fot at autox.team.net
>>> 
>>> http://www.fot-racing.com
>>> 
>>> Donate: http://www.team.net/donate.html
>>> Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
>>> Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/jsukey@gmail.com
>>> 
>>> 
>> _______________________________________________
>> fot at autox.team.net
>> 
>> http://www.fot-racing.com
>> 
>> Donate: http://www.team.net/donate.html
>> Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
>> Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/bownes@web9.com
>> 
>> 
> _______________________________________________
> fot at autox.team.net
> 
> http://www.fot-racing.com
> 
> Donate: http://www.team.net/donate.html
> Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
> Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/vfracing@aol.com
> 
> 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/fot/attachments/20210117/fedf6d8c/attachment-0003.htm>