[Healeys] BJ8 1967 Engine Rebuild failure

[Jim Bunte]

I foresee the swap as a big thing in the near future.


__________________

*Jim Bunte*
jim at jimbunte.com
310-497-7536



On Fri, Feb 9, 2024 at 6:54 PM <rfbegani at gmail.com> wrote:

> Funny you should suggest a v8 replacement.  Chris just made that
> suggestion to install an LS1 with GM Trans.  My Bother is a retired GM
> mechanic, and he agrees.  Did you do the exchange?  What engine trans etc.
> did you use?  All options are on the table.
>
>
>
> Bob
>
>
>
> *From:* HealeyRick <healeyrik at gmail.com>
> *Sent:* Friday, February 9, 2024 1:32 PM
> *To:* rfbegani at gmail.com
> *Cc:* healeys at autox.team.net
> *Subject:* Re: [Healeys] BJ8 1967 Engine Rebuild failure
>
>
>
> Sorry to hear this Bob. What you've been told so far seems correct.
> Without the main bearing caps you're in a tough spot.  Maybe trying to find
> a BJ8 block or a rebuildable BJ8 motor is the best of a bad group of
> choices.  Too bad, I gave away a bare block with caps from a BJ7 a few
> years ago for a donation to our club charity.  I'd put a wanted ad in the
> club magazines and Healey forums, Facebook pages and hope someone out there
> might have one. Try Hemphills, Healey Surgeons, David Nock, maybe they have
> one that needs rebuilding somewhere. Or do what I did and put a V8 in there!
>
>
>
> Best of luck,
>
> Rick Neville aka "HealeyRick"
>
>
>
> On Fri, Feb 9, 2024 at 11:12 AM <rfbegani at gmail.com> wrote:
>
> Gentlemen:
>
>
>
> I arrived back to Florida in May and decide to drive my 67 Austin-Healey.
> Drove it a mile and heard clanking engine, looked at the oil pressure, It
> was O! Instead of stooping to have towed home, I drove it back slowly.
> Last month, I dropped the pan and started to remove the rod and crank caps
> and bearings.  My mechanic friend said you got lucky the crank may only
> need polishing and new bearings.  So, I packed and marked each of the main
> bearing caps, bolts, and bearings along with piston rods and caps in
> individual plastic bags. Then packed them into a larger plastic bag which
> was put under the workbench near the garbage.  We towed the car to Mikes
> garage so he could pull and disassemble the engine.  Tuesday, he asked me
> to bring the parts I had removed from the engine so he would have
> everything in one place.  I looked around but could not find this black
> plastic bag and then remembered it got pitched in the garbage. So, I am now
> up the famous creek and am asking this group what I can do?
>
>
>
>    1. I am told the engine is finished because the Main Bearing caps are
>    not available and even if you could find them, they would need to be line
>    bored on the engine.
>    2. I am told that finding an engine block for a 3000 with original
>    main bearing caps is almost impossible.
>    3. Finding an engine to be rebuild might be possible.
>
>
>
> My engine was rebuilt 6000 miles with years ago everything new, so I would
> like to find a way of fixing the existing engine, if possible.
>
>
>
> Please give me your advice.
>
>
>
> Best regards,
>
>
>
> Bob Begani
>
> 67 Austin-Healey BJ8
>
>
>
>
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation  $12.75
>
> Archive: http://www.team.net/pipermail/healeys
> http://autox.team.net/archive/healeys
>
> Healeys at autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/healeyrik@gmail.com
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation  $12.75
>
> Archive: http://www.team.net/pipermail/healeys
> http://autox.team.net/archive/healeys
>
> Healeys at autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/jim@jimbunte.com
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/healeys/attachments/20240209/a353ddb9/attachment.htm>