[Shotimes] MAF connector question

[Carl Prochilo]

Jon,  You are in catch-up mode.  Check the SHOShop web site to get a
write-up on using an 80mm MAF application for the SHO.  That particular
MAF has been around for years.  (One noteable difference between that MAF
and say a Pro-M 77mm MAF is that the sampling tube for the Ford MAF is
inline while the Pro-M is off away from the primary airflow path.) 
Originally the 80mm MAF required an LPM to make up for calibration
differences, so that answers another of your questions below.
Best I can tell, the MAF connector is NOT an issue for either.  I have an
80mm Ford MAF sitting in my garage unused.
The throttle body opening is usually smaller than the MAF opening once you
upgrade.

Cheers,
Carl Prochilo
92 Ultra Red Crimson

> I have had excellent luck with just changing the sensors.  If the MAF you
> have came with a sensor attached and it wasn't originally set up for your
> SHO you might find that using your stock sensor will correct the problem.
> This is of course if the problem is due to calibration.  Then again, some
> housings do the calibration based on the size of the sample tube.  There
> are
> too many variables here to say for sure what's going on.  What concerns me
> most is the connector problem you mentioned.  Are you sure this MAF is for
> a
> Ford application?  I'm not sure Ford put a 80mm MAF on anything so it
> might
> be a motorsport item which could mean it was ordered for some specific
> calibration.   Please provide more information.  Maybe some pictures would
> be helpful.  Why do you need an 80mm MAF on a SHO anyway?  Don't they flow
> like 1000 CFM or something.  My Mustang runs 12's on a 73mm which if I
> recall correctly flows 850 CFM.  There's no way a 3.2 or 3.0 needs a MAF
> that large.  How big is your throttle body?
>
> Here's 2 examples of my MAF findings:
>
> Tried to put a 93 cobra MAF (housing and sensor) on my 88 Mustang.  It
> would
> not run correctly.  I swapped the sensor out with my stock one.
> Everything
> was fine after that.
>
> Got a new 73mm MAF housing for the Mustang.  Wouldn't want that cobra
> housing to go to waste so I installed it on my 93 SHO with the stock
> sensor.
> Runs great and there's a noticeable increase in performance.
>
> Is it safe to say that all stock ford housings have the same
> characteristics?  I'm thinking this is correct, at least in the Mustang
> world.  I was told once that the stock housings and sensors are all the
> same
> and all differences are compensated in the computer.  Makes sense but this
> doesn't explain why the cobra sensor didn't work in my car but who knows
> if
> it was any good to start with.  Remember, the reason that there are
> calibrated housings and sensors made by aftermarket companies are for
> people
> running non stock injectors with stock computers.  This is not how Ford
> does
> it!  Look at your MAF sensor (black plastic) and see if there is a sticker
> or if someone engraved anything into it.  This is a sure sign of an
> aftermarket cal.  I'd be willing to bet if you ordered a MAF for a mustang
> with stock injectors it would work fine on your SHO.  I've seen people
> selling SHO specific MAF's on eBay but I think they are full of crap.
> Please someone correct me if I'm wrong.  I am an electronic/RF tech by
> trade
> and I would love to learn more about this.  The entire Ford electronics
> system is something I have taken an interest in lately.  Any references or
> links would be greatly appreciated.
>
> Jonathan Zane KC2ENA
> 1988 Mustang LX
> 1995 Taurus SHO
> 1993 Taurus SHO
> 1979 F-150 4x4
> 1989 Ford Festiva
> 2001 Raptor
> www.njfourwheelers.com/jon.html
>
>
>
>> -----Original Message-----
>> From: shotimes-admin@autox.team.net
>> [mailto:shotimes-admin@autox.team.net] On Behalf Of Midwest
>> SHO Specialists
>> Sent: Friday, August 15, 2003 12:11 AM
>> To: shotimes@autox.team.net
>> Subject: Re: [Shotimes] MAF connector question
>>
>>
>> Joseph,
>>
>> I've never personally run across that problem.
>>
>> You could just crimp one piece of the plastic to form a press
>> fit over the male portion of the plug.  That should be enough
>> to hold it.
>>
>> Do you have an A/F chart with that MAF installed?  I have yet
>> to see a Ford 80mm MAF/ LPM combo that worked out of the box.
>>  The best gains come when you send Ted your chip and a chart.
>>
>> Mike Kopstain
>> Midwest SHO Specialists
>> 827 North Chestnut Avenue
>> Arlington Heights, IL 60004
>> www.MidwestSHO.com
>> Sales@midwestsho.com
>> ----- Original Message -----
>> From: "van Oss" <vanOss@centurytel.net>
>> To: <shotimes@autox.team.net>
>> Sent: Thursday, August 14, 2003 11:26 PM
>> Subject: [Shotimes] MAF connector question
>>
>>
>> > My 92 wears a Ford 80mm MAF (housing and sensor
>> electronics).   I recently
>> > had an intermittent CE light with bucking at anywhere above minimal
>> > throttle.
>> >
>> > Turns out, the "car" side of the MAF connector was slipping off the
>> > MAF. The physical dimensions of connectors seem to be a problem,
>> > because the connector will not latch.
>> >
>> > Has anyone else had this problem?  Should I just remove the prongs
>> > from
>> the
>> > connector?
>> >
>> > Joseph van Oss _______________________________________________
>> > Shotimes mailing list
>> > Shotimes@autox.team.net
>> > http://www.team.net/mailman/listinfo/shotimes
>> _______________________________________________
>> Shotimes mailing list
>> Shotimes@autox.team.net http://www.team.net/mailman/listinfo/shotimes
>>
>
> --
> This message was sent with an unlicensed evaluation version of
> Novell NetMail. Please see http://www.netmail.com/ for details.
> _______________________________________________
> Shotimes mailing list
> Shotimes@autox.team.net
> http://www.team.net/mailman/listinfo/shotimes