[Shotimes] Brake Bias Plugs

Sat, 8 Mar 2003 12:01:46 -0600

Damnit Bruce.... you keep pulling parts off that SLO.  When are you going to
break down and give me the damn headlights! :>)

Mike Kopstain
Midwest SHO Specialists
827 North Chestnut Avenue
Arlington Heights, IL 60004
www.MidwestSHO.com
Sales@midwestsho.com
----- Original Message -----
From: "Bruce Malachuk" <bmalach1@nycap.rr.com>
To: "'SHOtimes'" <shotimes@autox.team.net>
Sent: Saturday, March 08, 2003 10:41 AM
Subject: Re: [Shotimes] Brake Bias Plugs

> Well if the weather cooperates today I am gonna prolly pull the plugs
outta
> my 95 SE (since it just sits) and see about having them welded at local
shop
> here in town where I know the owner.
>
> ----- Original Message -----
> From: "Ian Fisher" <ianf@eden.rutgers.edu>
> To: "'Paul L Fisher'" <sho@paul-fisher.com>; "'Bruce Malachuk'"
> <bmalach1@nycap.rr.com>; "'SHOtimes'" <shotimes@autox.team.net>
> Sent: Saturday, March 08, 2003 11:37 AM
> Subject: RE: [Shotimes] Brake Bias Plugs
>
>
> > I haven't really looked at mine yet, but isn't what's in there threaded
> > just like the bypass plugs?
> >
> > Ian
> >
> >
> > -----Original Message-----
> > From: shotimes-admin@autox.team.net
> > [mailto:shotimes-admin@autox.team.net] On Behalf Of Paul L Fisher
> > Sent: Saturday, March 08, 2003 9:33 AM
> > To: Bruce Malachuk; SHOtimes
> > Subject: Re: [Shotimes] Brake Bias Plugs
> >
> >
> > I don't think I would trust not welding it. The material you will be
> > putting on the holes will be taking the few thousand PSI of the brake
> > fluid when you slam on the brakes. If there were a catastrophic failure
> > of the plug, you will be pumping large amounts of fluid onto the ground.
> >
> > Paul L Fisher
> > '93 Ford Taurus SHO Crimson Clearcoat ATX 171K Build date 11/18/1992
> > - K&N Panel filter, Tokico Struts, Eibach Springs, Dynomax cat-back,
> > Holley 190lph fuel pump, FPS rebuilt ATX, 26mm rear sway bar,
> > Performance-Plus Stainless Steel Y-pipe, '96 brake upgrade,
> > Proportioning valve plugs, Delrin sub-frame bushings, Amsoil Series 2000
> > 0W-30 oil, Amsoil Synthetic ATF. '00 Ford Explorer XLT 5.0L V8 AWD
> > Oxford White Clearcoat 41K Build date 11/19/1999
> > - Amsoil Series 2000 0W-30 oil, K&N Fuel Injection Performance Kit
> >
> > SHO Club member http://www.shoclub.com/
> > Check out my web site http://www.paul-fisher.com/
> > Amsoil dealer http://www.paul-fisher.com/oil.htm
> >
> > Get $5 free from Paypal! https://www.paypal.com/refer/pal=P3XEFFBFUFKN6
> >
> > ----- Original Message -----
> > From: "Bruce Malachuk" <bmalach1@nycap.rr.com>
> > To: "Midwest SHO Specialists" <SHOtimes@midwestsho.com>; "SHOtimes"
> > <shotimes@autox.team.net>
> > Sent: Friday, March 07, 2003 11:43 PM
> > Subject: Re: [Shotimes] Brake Bias Plugs
> >
> >
> > > well if I had a welder that that would be easy and I wouldn't have
> > > asked.
> > >
> > > ----- Original Message -----
> > > From: "Midwest SHO Specialists" <SHOtimes@midwestsho.com>
> > > To: "Bruce Malachuk" <bmalach1@nycap.rr.com>; "SHOtimes"
> > > <shotimes@autox.team.net>
> > > Sent: Saturday, March 08, 2003 12:35 AM
> > > Subject: Re: [Shotimes] Brake Bias Plugs
> > >
> > >
> > > > Not to oversimplify things Bruce, but you can remove your current
> > > > valves
> > > and
> > > > weld shut the hole in the end.  That's it. :>)
> > > >
> > > > Mike Kopstain
> > > > Midwest SHO Specialists
> > > > 827 North Chestnut Avenue
> > > > Arlington Heights, IL 60004
> > > > www.MidwestSHO.com
> > > > Sales@midwestsho.com
> > > > ----- Original Message -----
> > > > From: "Bruce Malachuk" <bmalach1@nycap.rr.com>
> > > > To: "SHOtimes" <shotimes@autox.team.net>
> > > > Sent: Friday, March 07, 2003 10:15 PM
> > > > Subject: [Shotimes] Brake Bias Plugs
> > > >
> > > >
> > > > > I've read everything on the shoforum about these, and they sound
> > pretty
> > > > > simple. Paul Nimz had listed some specs about them " The thread is
> > > M16x1.0
> > > > and
> > > > > you need two Vitron O-rings 3/8" OD x 1/4" ID x 1/16" and I was
> > > wondering
> > > > if
> > > > > anyonecould direct me to finding a local kind of place to get what
> >
> > > > > I
> > > need
> > > > to
> > > > > make my own? I'd buy some from SHOnut or Midwest SHO, but I wanted
> >
> > > > > to
> > > see
> > > > if I
> > > > > could make them myself. I can't imagine that they cost more than a
> >
> > > > > few
> > > > bucks
> > > > > to make. Like could I go to Home Depot and find something to use,
> > > > > or
> > > maybe
> > > > a
> > > > > plumbing supply place? Kinda want to do this for as little as
> > possible.
> > > > Maybe
> > > > > I could make plugs outta some JBweld, though that wouldn't be
> > > reversible.
> > > > >
> > > > > Thanks in advance
> > > > >
> > > > > Bruce
> > > > > _______________________________________________
> > > > > Shotimes mailing list
> > > > > Shotimes@autox.team.net
> > > > > http://www.team.net/mailman/listinfo/shotimes
> > > _______________________________________________
> > > Shotimes mailing list
> > > Shotimes@autox.team.net http://www.team.net/mailman/listinfo/shotimes
> > _______________________________________________
> > Shotimes mailing list
> > Shotimes@autox.team.net http://www.team.net/mailman/listinfo/shotimes
> _______________________________________________
> Shotimes mailing list
> Shotimes@autox.team.net
> http://www.team.net/mailman/listinfo/shotimes