[Shotimes] Vacuum Specs

[Paul Nimz]

This is from Helm.....

Intake Manifold Vacuum Test

Bring the engine to normal operating temperature. Connect Rotunda
Vacuum/Pressure Tester 164-R0253 or equivalent to the intake manifold
(9424). Run the engine at the specified idle speed.

The vacuum gauge should read between 51-74 kPa (15-22 in-Hg) depending upon
the engine condition and the altitude at which the test is performed.
SUBTRACT 4.0193 kPa (1 in-Hg) FROM THE SPECIFIED READING FOR EVERY 304.8 m
(1,000 FEET) OF ELEVATION ABOVE SEA LEVEL.

The reading should be quite steady. If necessary, adjust the gauge damper
control (where used) if the needle is fluttering rapidly. Adjust damper
until needle moves easily without excessive flutter.


Vacuum Gauge Readings--Interpretation

A careful study of the vacuum gauge reading while the engine is idling will
help pinpoint trouble areas. Always conduct other appropriate tests before
arriving at a final diagnostic decision. Vacuum gauge readings, although
helpful, must be interpreted carefully.

Most vacuum gauges have a NORMAL band indicated on the gauge face.



Following are potential gauge readings. Some are normal; others should be
investigated further.



1. NORMAL READING: Needle between 51-74 kPa (15-22 in-Hg) and holding
steady.

2. NORMAL READING DURING RAPID ACCELERATION AND DECELERATION: When engine is
rapidly accelerated (dotted needle), needle will drop to a low (not to zero)
reading. When throttle is suddenly released, the needle will snap back up to
a higher than normal figure.

3. NORMAL FOR HIGH-LIFT CAMSHAFT WITH LARGE OVERLAP: Needle will register as
low as 51 kPa (15 in-Hg) but will be relatively steady. Some oscillation is
normal.

4. WORN RINGS OR DILUTED OIL: When engine is accelerated (dotted needle),
needle drops to 0 kPa (0 in-Hg). Upon deceleration, needle runs slightly
above 74 kPa (22 in-Hg).

5. STICKING VALVES: When the needle (dotted) remains steady at a normal
vacuum but occasionally flicks (sharp, fast movement) down and back about 13
kPa (4 in-Hg), one or more valves may be sticking.

6. BURNED OR WARPED VALVES: A regular, evenly-spaced, downscale flicking of
the needle indicates one or more burned or warped valves. Insufficient
hydraulic valve tappet clearance will also cause this reaction.

7. POOR VALVE SEATING: A small but regular downscale flicking can mean one
or more valves are not seating.

8. WORN VALVE GUIDES: When the needle oscillates (swings back and forth),
over about a 13 kPa (4 in-Hg) range at idle speed, the valve guides could be
worn. As engine speed increases, needle will become steady if guides are
responsible.

9. WEAK VALVE SPRINGS: When the needle oscillation becomes more violent as
engine rpm is increased, weak valve springs (6513) are indicated. The
reading at idle could be relatively steady.

10. LATE VALVE TIMING: A steady but low reading could be caused by late
valve timing.

11. IGNITION TIMING RETARDING: Retarded ignition timing will produce a
steady but somewhat low reading.

12. INSUFFICIENT SPARK PLUG GAP: When plugs are gapped too close, a regular,
small pulsation of the needle can occur.

13. INTAKE LEAK: A low, steady reading which can be caused by an intake
manifold or throttle body mounting flange gasket leak.

14. BLOWN HEAD GASKET: A regular drop of fair magnitude can be caused by a
blown head gasket (6051) or warped head-to-block surface.

15. RESTRICTED EXHAUST SYSTEM: When the engine is first started and is
idling, the reading may be normal but as the engine rpm is increased, the
back pressure caused by a clogged muffler (5230), kinked tail pipe or other
concerns, will cause the needle to slowly drop to zero. The needle then may
slowly rise. Excessive exhaust clogging will cause the needle to drop to a
low point even if the engine is only idling.

 When vacuum leaks are indicated, pinpoint and correct the cause. Excess air
leaking into the system will upset the fuel mixture and cause concerns such
as rough idle, missing on acceleration or burned valves. If the leak exists
in the power brake, the system will not function correctly. ALWAYS FIX
VACUUM LEAKS.



Paul Nimz
'97 TR
'93 EG mtx





----- Original Message ----- 
From: "Bruce Malachuk" <bmalach1@nycap.rr.com>
To: "SHOtimes" <shotimes@autox.team.net>
Sent: Wednesday, May 21, 2003 12:25 PM
Subject: [Shotimes] Vacuum Specs


> I know I saw this posted somewhere, perhaps on the shoforum, but does
anyone
> have the vacuum specs for a SHO at idle, and then all the specs for
diferent
> maladies that can befall a car?
>
> Just wanted to see how my idle vac matches up.
>
> Thanks
>
> Bruce
> _______________________________________________
> Shotimes mailing list
> Shotimes@autox.team.net
> http://www.team.net/mailman/listinfo/shotimes