[Spridgets] Axle seal failure / wheel cylinder failure
Ron Soave
soavero at yahoo.com
Sun Sep 23 20:26:09 MDT 2018
Right Stuff is the best for quick set, and works really well on the plastic dipstick tube.
Ron Soave
> On Sep 23, 2018, at 9:06 PM, derf <derf247 at gmail.com> wrote:
>
> I'll have to order some and let the mechs at work try it out. I like Hylomar for stuff that gets changed a lot. We use The Right Stuff for some applications, good stuff.
>
>> On Sun, Sep 23, 2018 at 8:43 PM Ron Soave <soavero at yahoo.com> wrote:
>> I prefer it. It remains pliant but is meant for oil, gas, aldehydes, etc. can also take high heat. It has a Mil spec, Mil-a-46106 type 1 Group 1. Both are in the goop tote but I prefer 732. Bear in mind I change axles monthly and am constantly sealing things - lots of data points.
>>
>> Ron Soave
>>
>>> On Sep 23, 2018, at 7:50 PM, derf <derf247 at gmail.com> wrote:
>>>
>>> How does it compare to Hylomar?
>>>
>>>
>>>> On Sun, Sep 23, 2018, 4:26 PM Ron Soave via Spridgets <spridgets at autox.team.net> wrote:
>>>> Yes! You can forget the gasket and use a very small layer of Dow 732 schmutz. We use 732 on some stuff at work in very hostile environment space junk and it’s my fav stuff now.
>>>>
>>>> Ron Soave
>>>>
>>>> > On Sep 23, 2018, at 10:11 AM, Lester via Spridgets <spridgets at autox.team.net> wrote:
>>>> >
>>>> > So, a search of the 10,807 messages I still keep on my machine (Yes, really.) indicated that I asked the same questions in 2009.
>>>> >
>>>> > In 9 years has anything changed? Are there new seals that are the bees knees? I don’t think that I need new bearings as the miles are low enough.
>>>> >
>>>> > Just to be sure I need to:
>>>> >
>>>> > Undo the retaining screw
>>>> >
>>>> > Lever the axle out and free of the hub
>>>> >
>>>> > Undo lock washer
>>>> >
>>>> > Undo hub nut
>>>> >
>>>> > Jury rig a device to pull hub
>>>> >
>>>> > Pull out seal
>>>> >
>>>> > Install new seal
>>>> >
>>>> > Reinstall hub, lock washer,nut (Any tips welcome, all the video shows work with rear end removed from car.)
>>>> >
>>>> > Install new “O” ring
>>>> >
>>>> > Install new paper gasket
>>>> >
>>>> > Install axle
>>>> >
>>>> > Congratulate myself on a job well done?
>>>> >
>>>> > ------------------------
>>>> >
>>>> > spridgets at autox.team.net
>>>> >
>>>> > Donate: http://www.team.net/donate.html
>>>> > Suggested annual donation: $12.75
>>>> >
>>>> > Archive: http://www.team.net/pipermail/spridgets
>>>> >
>>>> > Unsubscribe/Manage: http://autox.team.net/mailman/options/spridgets/soavero@yahoo.com
>>>>
>>>> ------------------------
>>>>
>>>> spridgets at autox.team.net
>>>>
>>>> Donate: http://www.team.net/donate.html
>>>> Suggested annual donation: $12.75
>>>>
>>>> Archive: http://www.team.net/pipermail/spridgets
>>>>
>>>> Unsubscribe/Manage: http://autox.team.net/mailman/options/spridgets/derf247@gmail.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://autox.team.net/pipermail/spridgets/attachments/20180923/41073d37/attachment.html>
More information about the Spridgets
mailing list