You can't really "grind back" the composite gasket and still have it
seal. You need to gingerly uncrimp the sandwich around the valve
pocket, then cut back the inner asbestos-like material, then gingerly
recrimp the two copper sides back together. It's easy to tear the
copper in the process.
Tony
At 09:59 AM 11/24/2012, Tylerpthompson@yahoo.com wrote:
>I pulled the head off of mine a few mons back. If folks recall, I
>broke 7 of 8 tops of the outer valve springs and one inner. I am
>fixing that and checking geometry.
>
>I do have oversized valves and 89 bore, and I found my Payen A330
>gasket was burnt where the gasket was not ground back. My sleeves
>are not ground back as well.
>
>Can you grind back the copper Payen gasket with no issues? I will be
>feathering back the sleeves as well.
>
>Also, does anyone know the correct valve spring height?
>
>Thx
>
>Ty
>
>
>Sent from my iPad
>(Please excuse any errors or typos)
>
>On Nov 15, 2012, at 7:41 PM, Joe Alexander <n197tr4@cs.com> wrote:
>
> > Ditto...Using Payen for several years now and has been one less
> thing to worry
> > about.
> >
> >
> >
> >
> > Joe Alexander
> >
> > Subject: Re: [Fot] trt 3/4 head gasket
> >
> >
> > Like Tony we use a stock Payen gasket notched to fit the larger
> valve with no
> > problem. My take is that one must make sure the head & block are
> flat & true
> > &
> > properly installed.
> >
> > Sent from my iPhone
> >
> > On Nov 15, 2012, at 12:36 AM, Tony Drews <tony@tonydrews.com> wrote:
> >
> >> I use a stock composite gasket and will get a season out of it. I was at
> > about 0.175 milled, am now at 0.130 after my last head gasket
> problem turned
> > out to be a collapsing combustion chamber in the head problem. I
> don't have
> > giant valves (they clear the 87 mm liners), so I notched the liner to match
> > the "mickey ear" of the stock gasket so there was something
> supporting it on
> > one side in the pocket that disappeared. I put the seam side against the
> > liner then.
> >>
> >> Tony Drews
> >>
> >> At 12:18 PM 11/10/2012, KENMUN@aol.com wrote:
> >>> anyone having success with the stock composite head gasket on a milled
> >>> head. my head has been milled .150" and the intake valve
> pockets are gone.
> > i'm
> >>> not having much luck with the steel gasket.
> >>> thanks, ken m. tr 3 vintage racer.
> >>> _______________________________________________
> >>> fot@autox.team.net
> >>>
> >>> http://www.fot-racing.com
> >>>
> >>> Donate: http://www.team.net/donate.html
> >>> Archive: http://www.team.net/archive
> >>> Forums: http://www.team.net/forums
> >>> Unsubscribe: http://autox.team.net/mailman/options/fot/tony@tonydrews.com
> >> _______________________________________________
> >> fot@autox.team.net
> >>
> >> http://www.fot-racing.com
> >>
> >> Donate: http://www.team.net/donate.html
> >> Archive: http://www.team.net/archive
> >> Forums: http://www.team.net/forums
> >> Unsubscribe: http://autox.team.net/mailman/options/fot/jhhasty@gdhs.com
> > _______________________________________________
> > fot@autox.team.net
> >
> > http://www.fot-racing.com
> >
> > Donate: http://www.team.net/donate.html
> > Archive: http://www.team.net/archive
> > Forums: http://www.team.net/forums
> > Unsubscribe: http://autox.team.net/mailman/options/fot/n197tr4@cs.com
> > _______________________________________________
> > fot@autox.team.net
> >
> > http://www.fot-racing.com
> >
> > Donate: http://www.team.net/donate.html
> > Archive: http://www.team.net/archive
> > Forums: http://www.team.net/forums
> > Unsubscribe:
> http://autox.team.net/mailman/options/fot/tylerpthompson@yahoo.com
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/fot/mharc@autox.team.net
|