fot
[Top] [All Lists]

[Fot] TR3/4 Rear Main Seal

Subject: [Fot] TR3/4 Rear Main Seal
From: jwheeler1947 at yahoo.com (Jack Wheeler)
Date: Tue, 24 Jan 2017 23:39:14 +0000 (UTC)
References: <20170120.195748.28748.0@webmail07.dca.untd.com> <20170121081226.ADC451310F3@relay.mailchannels.net> <1687323984.1520142.1485013424485@mail.yahoo.com> <F85D042A-8DBB-4CB8-9C7F-C64D8F7E8C09@att.net> <699af90eb81a4a88a26179181f29fb03@Server-Ex.RevingtonTR.local>
?I have received a huge number of responses to my questions about crankshaft 
rear seal modifications for TR-3 and TR-4 engines.? In fact, I think there must 
be as many different approaches as there are members of the FOT.? Thanks for 
the ideas.? It sure gives me something to think about.
Thanks again.
Jack

     
----- Forwarded Message -----
 From: Neil Revington <neil at revingtontr.com>
 To: Paul Ricco <paulricco at att.net>; Jack Wheeler <jwheeler1947 at 
yahoo.com> 
Cc: Tony Drews <tony at tonydrews.com>; Joe Boruch <jaboruch at netzero.net>; 
"fot at autox.team.net" <fot at autox.team.net>
 Sent: Monday, January 23, 2017 12:34 PM
 Subject: RE: [Fot] TR3/4 Rear Main Seal
   
 <!--#yiv5551074761 _filtered #yiv5551074761 {font-family:Wingdings;panose-1:5 
0 0 0 0 0 0 0 0 0;} _filtered #yiv5551074761 {font-family:"Cambria 
Math";panose-1:2 4 5 3 5 4 6 3 2 4;} _filtered #yiv5551074761 
{font-family:Calibri;panose-1:2 15 5 2 2 2 4 3 2 4;} _filtered #yiv5551074761 
{font-family:Mistral;panose-1:3 9 7 2 3 4 7 2 4 3;} _filtered #yiv5551074761 
{font-family:"Arial Narrow";panose-1:2 11 6 6 2 2 2 3 2 4;} _filtered 
#yiv5551074761 {font-family:"Helvetica Neue";}#yiv5551074761 #yiv5551074761 
p.yiv5551074761MsoNormal, #yiv5551074761 li.yiv5551074761MsoNormal, 
#yiv5551074761 div.yiv5551074761MsoNormal 
{margin:0cm;margin-bottom:.0001pt;font-size:12.0pt;font-family:"Times New 
Roman", serif;}#yiv5551074761 a:link, #yiv5551074761 
span.yiv5551074761MsoHyperlink 
{color:blue;text-decoration:underline;}#yiv5551074761 a:visited, #yiv5551074761 
span.yiv5551074761MsoHyperlinkFollowed 
{color:purple;text-decoration:underline;}#yiv5551074761 
span.yiv5551074761EmailStyle17 {font-family:"Calibri", 
sans-serif;color:#1F497D;}#yiv5551074761 .yiv5551074761MsoChpDefault 
{font-size:10.0pt;} _filtered #yiv5551074761 {margin:72.0pt 72.0pt 72.0pt 
72.0pt;}#yiv5551074761 div.yiv5551074761WordSection1 {}-->Hi Paul, Thanks for 
copying me in on this. My only comment would be that Hylamar is not ideal as it 
can ?ball off? and when that happens rubbery bits of goo end up in oil ways. 
You should use the original product Wellseal  
http://www.revingtontr.com/product/600569a/name/wellseal-jointing-compound-100ml
 or the superior sealant Heldite 
http://www.revingtontr.com/product/tdc5001-125/name/heldite-125ml-tin-with-applicator
 or of course any other similar product. Anything by silicone sealant.  ? 
Cheers  ? Neil Revington
Revington TR Ltd?
Thorngrove Barns,
Middlezoy, 
Somerset, TA7 0PD.
England
( +44(0)1823 698437
Fax:- +44(0)1823 698109
-neil at revingtontr.com
web: www.revingtontr.com Every part you need for your TR, new or second hand, 
standard or improved. Connect with Revington TR: ????  ? Suppliers of Standard 
and uprated parts to?TR enthusiasts  ? From: Paul Ricco [mailto:paulricco at 
att.net]
Sent: 21 January 2017 18:29
To: Jack Wheeler <jwheeler1947 at yahoo.com>
Cc: Tony Drews <tony at tonydrews.com>; Joe Boruch <jaboruch at netzero.net>; 
fot at autox.team.net
Subject: Re: [Fot] TR3/4 Rear Main Seal  ? We have some experience with rear 
main seal issues on our TR4 race motor. ?When we purchased our car, all of the 
cranks that were included had already been machined and the scroll removed. ?We 
have been able seal the engines successfully with careful preparation using 
these cranks and we have been happy with the results. ?Here is what we learned: 
 ? 1. ?The Revington Seal Kit does work very well when it is installed 
properly. ?It is good product. ?  ? 2. ?There are a lot of cranks floating 
around that had the scroll removed, but they were not machined to the correct 
size for the seal kit. ?We have found some that have been machined too small 
and one that was too large. ?Too large was just as big a problem, because the 
seal could not close all the way around the crank causing a leak with the oil 
pressures that we run.  ? 3. ?The aluminum seal housings are often not 
installed and sealed correctly. ?The problem is further compounded by the felt 
seal not being completely sealed when the rear main bearing cap is installed. 
?We use 1 inch pieces of the felt soaked in Permatex Aviation Sealer and pack 
them in tight. ?It is messy, ?but seams to work well.  ? 4. ?Measure your crank 
seal surface very carefully. ?If it is too small or too large, the seal will 
not work correctly. ?Both issues can be corrected. ?Have a good machine shop 
read the instructions and help you get the crank prepped per the instructions 
that come with the seal kit.  ? 5. ?Make sure that the machine shop leaves the 
correct radius corner when they machine the scroll off.  ? 6. ?Follow the 
instructions that Revington includes in his kit to the letter, and the seal 
will work great in racing applications.  ? 7. ?I will only use replacement 
seals for our housings that are purchased directly from Revington TR. ?I have 
been told that another vendor tried to have some produced and they may not be 
the correct size and specification for the Revington housing. ?Going to 
Revington TR for the replacements solves that issue.  ? 8. ?Choose the sealant 
that you use for the housing very carefully. ?We have had very good success 
with Hylomar. ?There may be other good choices but that has worked for us.  ? 
Hope some of this helps and best of luck getting the motor sealed up.  ? Paul 
Ricco TR4 Blue #4  ? 

Sent from my iPad 
On Jan 21, 2017, at 9:43 AM, Jack Wheeler via Fot <fot at autox.team.net> 
wrote: 
Before the Viton seal became available, I used a couple of different approaches 
to keeping the crankcase sealed at 7,000 RPM's, both involved machining off the 
scrolling from the rear of the crankshaft.? The first was to use a rope seal, 
like the E-Type Jaguar.? I took the dimension off the Jag crank, then machined 
the Triumph crank to the same OD.? I used the stock Triumph aluminum seal to 
hold the rope seal in place. 

 My next attempt was a big block Chevy, 2 part neoprene seal.? Again, I 
machined the Triumph crank surface where the seal rides to the same OD as the 
Big Block Chevy Crank.? Then I machined a two part aluminum retainer, similar 
to the stock Triumph rear seal, but with the inside machined to hold the Chevy 
seal in place.? I think there was a kit available at one time, were you could 
buy the seal, and the adapter that holds it in place (Moss (?) or someone like 
that had made up the same aluminum adapter that I had, and were selling it as a 
kit).? Anyway, this worked pretty well as long as you got the Chevy seal well 
centered around the crankshaft. 

 You might go to a junk yard (or speed shop) and find out what the dimension of 
the big block Chevy crank is, at the point where the rear seal rides against 
the crank.? If your cranks can be machined to this diameter, then see if you 
can find one of the old Moss conversion kits.? When I sold my race car to Don 
Marshall (#11 EP TR-4A - Runoffs winner 1990), there were 2 or 3 of these seal 
adapters that went with it.? If you can track it down, see if one of these seal 
adapters is available (out of an engine), and could be used as a sample to have 
one machined.? Or, you could do like I did.? Buy the big block Chevy seal, and 
use it as a template, along with a stock Triumph rear seal, to figure the 
dimensions needed to machine a two part adapter.? This may seem like a lot of 
work, but if your cranks are good, it might be cheaper than getting a new 
crank, especially if you have good machining capability available. 

 Good luck, and let me know what you decide. 

 Jack

  ? From: Tony Drews via Fot <fot at autox.team.net>
To: Joe Boruch <jaboruch at netzero.net>;fot at autox.team.net 
Sent: Saturday, January 21, 2017 3:12 AM
Subject: Re: [Fot] TR3/4 Rear Main Seal 
I did get the message but don't have any alternate suggestions for 
rear seal if the crank is machined for the earlier seal kits.

- Tony Drews

At 06:57 PM 1/20/2017, Joe Boruch via Fot wrote:
>Not sure if this went thru before, since I did not receive it in my 
>inbox and did not receive any replies.? Sorry for the duplication, 
>if it went out previously.
>
>The recent discussion of the valve cover gasket reminded me to ask 
>about TR3/4 rear main seals.? I know that the new improved Viton 
>seals are make to fit cranks that the scroll surface has not been 
>machined.? All my cranks have been machined to fit the earlier seal 
>kits.? Is there an upgraded seal kit to fit machined cranks or would 
>there even be any advantage to using the new seal?? Joe(B)
>
>
>fot at autox.team.net
>
>http://www.fot-racing.com
>
>Donate: http://www.team.net/donate.html
>Archive: http://www.team.net/archive
>Forums: http://www.team.net/forums
>Unsubscribe/Manage: 
>http://autox.team.net/mailman/options/fot/tony at tonydrews.com 


_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Archive: http://www.team.net/archive

  ? 

_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Archive: http://www.team.net/archive

 


   
-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
<http://autox.team.net/pipermail/fot/attachments/20170124/01173921/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.gif
Type: image/gif
Size: 1252 bytes
Desc: not available
URL: 
<http://autox.team.net/pipermail/fot/attachments/20170124/01173921/attachment.gif>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image002.gif
Type: image/gif
Size: 1421 bytes
Desc: not available
URL: 
<http://autox.team.net/pipermail/fot/attachments/20170124/01173921/attachment-0001.gif>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image003.gif
Type: image/gif
Size: 899 bytes
Desc: not available
URL: 
<http://autox.team.net/pipermail/fot/attachments/20170124/01173921/attachment-0002.gif>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image004.gif
Type: image/gif
Size: 1378 bytes
Desc: not available
URL: 
<http://autox.team.net/pipermail/fot/attachments/20170124/01173921/attachment-0003.gif>

<Prev in Thread] Current Thread [Next in Thread>
  • [Fot] TR3/4 Rear Main Seal, Jack Wheeler <=