fot
[Top] [All Lists]

[Healeys] Caliper Piston Dustcover

Subject: [Healeys] Caliper Piston Dustcover
From: michael.salter at gmail.com (michael.salter at gmail.com)
Date: Mon, 27 Mar 2017 12:16:53 +0000 (UTC)
References: <CAA-dtXag81KPCpeKbiy=ajU4DJ-2rO1_Mai=w0QkpG7ycenpMg@mail.gmail.com> <20170327041550.Q9GEP.11688.root@cdptpa-web12>

Hi Mike,

Installing those dust covers can be very difficult however with patience and 
liberal application of brake grease it can be achieved. 

First, as Greg mentioned it it imperative that both the grooves in the body are 
scrupulously clean. Scrape around with a dental pick to ensure that any rust is 
removed. 

Now insert the piston seal fully into the lower groove being sure to press it 
fully home with your thumbs. Apply a little brake grease to it.

Next insert the lower lip of the dust seal into the upper groove again being 
sure to press it fully home with your thumbs.

Now lightly? press the closed end of the greased piston against the dust seal 
and use a small wire hook to lift the outer lip of the dust seal onto the 
outside of the piston.

Now it will be possible to wiggle the piston? into the bore through both seals. 
DO NOT FORCE IT IN. LIGHT THUMB PRESSURE SHOULD BE ALL THAT IS REQUIRED. 

Finally use a dental pic to guide the outer lip of the dust seal into its 
groove in the piston. 

Only 3 to go...

Michael S 

BN1 #174

With 4 wheel drum brakes. ?






From: glemon at neb.rr.com

Sent: Monday, March 27, 12:23 AM

Subject: Re: [Healeys] Caliper Piston Dustcover

To: healeys at autox.team.net, Mike Tobin



Mike, I had the same issue on my TR250 (same brakes as a BJ8). Spent the better 
part of a Saturday trying to get them on, got a couple on, tore a couple, 
ordered another kit. The new kit was much easier, though still a bit finicky, 
the rubber was slightly thinner and it made everything fit much better. I don't 
remember where I sourced either, but the first set was obviously not that well 
made. Also if you are working with used parts make sure the grooves and 
everything are cleaned out very thoroughly. Greg Lemon 68 TR250 ---- Mike Tobin 
wrote: > Hi, If anyone is still out there. > I got the caliper apart and 
cleaned (thanks all) and now I'm having trouble > getting the pistons in with 
the dust covers. > I can get the piston in or I can get the dust cover seated 
in its slot in > the cylender. I can't get both. > If I put the piston in first 
I can't get the cover into its slot. If I put > the cover in first I can't keep 
it in position and while installing the > piston. > I know I've done this back 
in the day and I don't remember having any > problem (or maybe I just said 
"Screw It!" and only fit the cover to the > piston). > Cheers, > Mike Tobin, > 
Townsend, Montana _______________________________________________ Support 
Team.Net http://www.team.net/donate.html Suggested annual donation $12.75 
Archive: http://www.team.net/archive Forums: http://www.team.net/forums Healeys 
at autox.team.net http://autox.team.net/mailman/listinfo/healeys 
Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/michaelsalter 
at gmail.com 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
<http://autox.team.net/pipermail/healeys/attachments/20170327/4e2e83b4/attachment.html>

<Prev in Thread] Current Thread [Next in Thread>