fot
[Top] [All Lists]

[Healeys] 100 Windshield Assembly

Subject: [Healeys] 100 Windshield Assembly
From: greylinn at ozemail.com.au (Peter & Veronica)
Date: Sat, 27 May 2017 07:25:13 +1000
References: <453429131.2601101.1495736247985.ref@mail.yahoo.com> <453429131.2601101.1495736247985@mail.yahoo.com> <b4e734ad-87bb-9107-d0e9-aa1a4368ee4f@comcast.net> <1013791.158453.1495762148217@mail.yahoo.com> <05bf8517-2b5a-c016-1246-829b40815467@comcast.net> <994440482.432178.1495811155541@connect.xfinity.com>
...best thing to use is uncured rubber strip ? you moisten it with kerosene 
which makes it slippery ? much easier to fit

Cheers

Peter

From: Charlie Baldwin 
Sent: Saturday, May 27, 2017 1:05 AM
To: Healeys at autox.team.net 
Subject: Re: [Healeys] 100 Windshield Assembly

When I did a couple of BT7 windshields some years ago the Moss rubber was way 
too thick.  Even though it is rubber it isn't very compressible.  I measured 
the thickness of the glass and channel and determined what thickness rubber was 
required, which I got from Restoration Specialties in Windber, PA.  They have 
an online catalog, but I think they call it glazing tape.  I put contact cement 
on the rubber and the windshield to keep the rubber wrapped around while 
tapping the frame onto the glass.  The new glass wasn't at the same radius as 
the old frame and one of the windshields broke down the middle after it was in 
a while due to too much stress on the glass.  Then I had to relieve the radius 
of the frame a bit to match the replacement glass.


  On May 26, 2017 at 12:28 AM Bob Spidell <bspidell at comcast.net> wrote:


  IIRC, the discussion about 'too thick' rubber was for the U-channel seal, but 
I may not RC.  The glazing rubber we got from Moss years ago seemed to be the 
correct thickness.  I don't recall using a mallet or much force at all, nor do 
I recall using any lubrication, but it was a long time ago.

  Did you get the Triplex windshield, or the cheaper one?  There may be some 
issues with thickness between the two.  We were able to reuse the windshield 
that came with the car--I spent a day polishing out wiper scratches--and AFAIK 
it was original, or an OEM replacement.

  Bob




  On 5/25/2017 6:29 PM, Michael MacLean wrote:

    Thanks Bob.  I have the glazing rubber from Moss, but I seem to remember a 
problem a while ago about the rubber being too thick I hope not.  The only 
other question I might have is, did you use a rubber mallet? Do you need some 
kind of lubrication?  It looks to be a tight fit. Once it is on, I won't be 
able to move laterally if it's too far to the right or left.  Sounds like you 
have to get ot right the first time. 
    Mike







 

  _______________________________________________
  Support Team.Net http://www.team.net/donate.html
  Suggested annual donation $12.75
  Archive: http://www.team.net/archive
  Forums: http://www.team.net/forums

  Healeys at autox.team.net
  http://autox.team.net/mailman/listinfo/healeys

  Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/mgcharlie 
at comcast.net




--------------------------------------------------------------------------------
_______________________________________________
Archive: http://www.team.net/archive

Healeys at autox.team.net
http://autox.team.net/mailman/listinfo/healeys


-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
<http://autox.team.net/pipermail/healeys/attachments/20170527/615f4f6c/attachment.html>

<Prev in Thread] Current Thread [Next in Thread>