fot
[Top] [All Lists]

[Healeys] cable

Subject: [Healeys] cable
From: thehartnetts at earthlink.net (Len and/or Marge Hartnett)
Date: Mon, 29 May 2017 10:16:45 -0700
References: <1e2fd9a2-45aa-4044-28e2-bbf578eb4cc0@comcast.net> <e5963a35-3c1e-3f48-1320-10f91adcc828@comcast.net> <1b00e9fa-dde1-99bb-c0c4-9604385a2249@comcast.net>
I have had two occasions where the speedo has stopped working.  In both cases, 
it was because the right angle drive at the transmission had come apart and the 
gear had fallen out.  The "cap" is similar to a freeze plug on the engine.  
Concave shape that you tap to expand it when it is installed.  Luckily, all the 
parts fell onto the "X" member of the frame which is right below it and were 
recovered even after having driven several miles.  As I recall, there is the 
cap, a special spacer, and the gear.  I replaced the innards, and secured the 
cap by restoring its concave shape and then tapping it tight again.

Having looked at Bob's link, below, page 2, I believe that I do not have the 
washer installed that is recommended.  I will check this the next time I have 
the tunnel up or out.  I say "up" because you do not need to remove the tunnel 
cover, just get the back end of it up enough to access the angle drive.  
Getting to it from underneath may be less time consuming but I have never tried 
it.

(The Other) Len
Fairfield, CA, USA
1967 AH 3000 MkIII, HBJ8L39031
        215,543  miles

  ----- Original Message ----- 
  From: Bob Spidell 
  To: healeys at autox.team.net 
  Sent: Monday, May 29, 2017 6:46 AM
  Subject: Re: [Healeys] cable


  There were some defective cables going around a few years ago but, IIRC, they 
were a bit too long at the speedo end and damaged the speedo.

  I've never heard of a speedo cable breaking--they usually just kink--but I'm 
sure it's possible, esp. if it got locked up inside the speedo.  Check that the 
cable hasn't just come loose at the OD end (though not likely as it would be 
too long to go properly back into the speedo).  You can do this by futzing with 
the inner cable at the speedo until you feel it go into the drive, at which 
point it should resist turning.  You're right, it's odd the cable would come 
loose at the speedo end.  But, the connector is a very fine thread and it would 
be easy to cross-thread; maybe someone just got frustrated with it and jammed 
it on?


  My gut feeling is the adapter is broken somehow, but more investigation is 
warranted.  The adapter should have a small copper washer acting as a spacer 
for the cable; the adapter can fail if this washer is missing: 
http://www.mossmotors.com/graphics/products/PDF/021-511.pdf


  Bob




  On 5/28/2017 8:56 PM, Mike S wrote:

    Interestingly, the speedo was working fine, until one day it didn't.  No 
warning.  I decided to unhook the connection at the back of the speedo and see 
if the square end of the cable was rotatable.  To my surprise, the entire cable 
was not even connected to the speedometer.  Just hanging loose.  Since it takes 
quite a few turns to screw it on, this seems odd.  Connecting it did not solve 
the problem.  Anyway, the cable itself turns quite easily; does this mean the 
cable itself is broken?  If so, I will have to pull each end out separately.  
It's a real pain to get under the car, as it is an inch off the ground (it 
seems), and I am more than an inch thick.  Working from the top as Bob 
suggested sounds better. 
    Mike



-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
<http://autox.team.net/pipermail/healeys/attachments/20170529/8ea0beea/attachment.html>

<Prev in Thread] Current Thread [Next in Thread>