mgs
[Top] [All Lists]

RE: Body Work Preparation - Rust and Bondo

To: "Larry Hoy" <larryhoy@prodigy.net>,
Subject: RE: Body Work Preparation - Rust and Bondo
From: "BMack" <bmack99@home.com>
Date: Fri, 15 Sep 2000 11:44:22 -0700
Larry,

I agree with you on this but if Mike is looking at a TEMPORARY repair and
doing it right in a couple of years then grinding down the paint and as MUCH
rust (anticipating it is just surface rust) and putting a product called
"RUST MORT" on will solve the problem temporarily and you can fill over top
of it and prep as necessary.

Remember put some kind of paint on it as primer is not waterproof.

IF there is RUST THRU your sunk, bondo will NEVER help.

"Restoringly" Yours,
Bryce Mack
Classic Auto Restoration Services
BODYWORK - METALFORMING - PREP & PAINT - WOODWORK
Web Page: http://members.home.net/bmack99/paneldoctor/
FAQ's - How-To's - Tools



-----Original Message-----
From: owner-mgs@autox.team.net [mailto:owner-mgs@autox.team.net]On
Behalf Of Larry Hoy
Sent: Friday, September 15, 2000 7:22 AM
To: Graziano, Michael
Cc: mgs@autox.team.net
Subject: RE: Body Work Preparation - Rust and Bondo


Replace the section with a repair panel.  If you don't do this the rust will
return, trust me.

Larry Hoy

-----Original Message-----
From: owner-mgs@autox.team.net [mailto:owner-mgs@autox.team.net]On Behalf Of
Graziano, Michael
Sent: Friday, September 15, 2000 8:00 AM
To: 'Spridgets'
Cc: 'mgs@autox.team.net'; 'spitfires@autox.team.net'
Subject: Body Work Preparation - Rust and Bondo

All,

I'd like to start working on that bit of rust on my lower quarterpanel
(behind the rear passenger wheel).  It's limited to the piece below the
moldings, so paint matching doesn't have to be perfect.

My question has to do with rust and bondo.  After I wire brush out the rust,
I'd like to put some type of rust inhibiter to prevent the cancer from
spreading.   Spray Can Rustoleum Primer has always worked well on my wrought
iron fences and lawn furniture.  But I'm not sure if the bondo will hold to
the paint.  If I apply the bondo directly to the bare metal,  I'm worried
the water that's trapped might cause the rust to begin again.  This needs to
last a few years as I can't spend the money right now to have the work
professionally done.

I only need a light layer of Bondo to fill up the rust depleted portion of
the fender.  It shouldn't be more than 1/4" at the worst spot.

Is spray can primer OK after the the bondo work has been done?  Any
recommendations or words of advice?

Mike


[INFO] -- Content Manager:
This message is for the named person's use only.  It may contain
confidential, proprietary or legally privileged information.  No
confidentiality or privilege is waived or lost by any mistransmission.
If you receive this message in error, please immediately delete it and all
copies of it from your system, destroy any hard copies of it and notify the
sender.  You must not, directly or indirectly, use, disclose, distribute,
print, or copy any part of this message if you are not the intended
recipient. CREDIT SUISSE GROUP and each of its subsidiaries each reserve
the right to monitor all e-mail communications through its networks.  Any
views expressed in this message are those of the individual sender, except
where the message states otherwise and the sender is authorised to state
them to be the views of any such entity.
Unless otherwise stated, any pricing information given in this message is
indicative only, is subject to change and does not constitute an offer to
deal at any price quoted.
Any reference to the terms of executed transactions should be treated as
preliminary only and subject to our formal written confirmation.



<Prev in Thread] Current Thread [Next in Thread>