spridgets
[Top] [All Lists]

[Spridgets] Tips or examples installing my Facet pump, hose never fits

Subject: [Spridgets] Tips or examples installing my Facet pump, hose never fits right.
From: grunthaner at gmail.com (Linda Grunthaner)
Date: Tue, 17 May 2011 06:10:43 -0400
References: <BANLkTinDOFSE8euAoT4zaBT_poMiZxJvNw@mail.gmail.com> <1348869023-1305426970-cardhu_decombobulator_blackberry.rim.net-1809670959-@b3.c12.bise6.blackberry>
Steve if it is the same pump it is designed to push not pull, from what I'm
told.

Lin

On Sat, May 14, 2011 at 10:36 PM, <an5.sprite at gmail.com> wrote:

> If you can not get a 90 degree fitting you may be able to find a 90 degree
> street elbow and just screw the fitting into that.
>
> I placed my filter under the hood right before the carbs (but away from the
> exhust manifold) Easier to change and it will filter anything that comes
> from the fuel line.
>
> Steve
> Sent from my Verizon Wireless BlackBerry
>
> -----Original Message-----
> From: Linda Grunthaner <grunthaner at gmail.com>
> Sender: spridgets-bounces at autox.team.net
> Date: Sat, 14 May 2011 22:01:34
> To: Spridget list<spridgets at autox.team.net>
> Subject: [Spridgets] Tips or examples installing my Facet pump,
>  hose never fits  right.
>
> List,
> I am installing my new Facet fuel pump in the rear like the later Spridgets
> and came to a small road block. Below are photos of the location and the
> new
> pump for a better visual. I drained the tank today (the crap ran down my
> arm
> so i am soaked with gas (good thing I quit smoking again this week) and I
> was getting ready to cut the fuel line but noticed when I place the pump in
> position it is very cramped and I don't see how to get rubber line in
> correctly without kinking the line for that 90 degree turn. I couldn't get
> to the store in time but I'll try and get a fitting with a 90 degree which
> I'm sure they won't have the correct thread size or the end will be huge. I
> also checked my rubber line and it is 1/4" as I recall our lines are
> smaller
> than stock fuel line and are a pain in the ass to fit because we end up
> with
> larger hose. Is there a specialty parts shop who will have a fitting for
> small hose?
>
> Why is this such a PITA it just shouldn't be. Looking at the filter that
> came with the pump I won't be able to fit any hose on that monster can I
> remove the filter altogether or maybe get a fitting and a plastic filter?
> Also I remember an old post that said they make teflon tape for fuel, who
> would have that?
>
> If anyone can send me a photo of their setup I would be appreciative.
> Lin
> My pictures:
> http://www.spritespot.com/gallery/Deep-Pink-Sprite/location
>
> http://www.spritespot.com/gallery/Deep-Pink-Sprite/placement
> _______________________________________________
>
> Donate: http://www.team.net/donate.html
> Suggested annual donation  $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/spridgets/an5.sprite at gmail.com

<Prev in Thread] Current Thread [Next in Thread>