datsun-roadsters
[Top] [All Lists]

Re: Which is number 1 cylinder?

To: "Adam Bradley" <ambradley@yahoo.com>,
Subject: Re: Which is number 1 cylinder?
From: "roadster" <roadster@rcn.com>
Date: Tue, 27 Mar 2001 20:58:09 -0800
Adam,

It doesn't really matter. As I said in an earlier post today, the only way
to tell whether #1 on the distributor is towards the radiator or towards the
firewall is to match the orientation of the valves at 0 degrees TDC (end of
compression stroke before firing).

If you look at the Clymers manual (copy of Nissan's) in the 2000 engine
section, they describe installing the thingee (distributor drive gear). The
text says 11:25 position for the off-center slot, with the smaller
semi-circle MUST be placed toward the FRONT. The picture (Fig EM-128) shows
the LARGER semi-circle towards the FRONT. Even they were confused!

Fred - So.SF
BADROC

----- Original Message -----
From: "Adam Bradley" <ambradley@yahoo.com>
To: "WILSON,BOB (A-SantaClara,ex1)" <bob_wilson@agilent.com>;
<datsun-roadsters@autox.team.net>
Sent: Tuesday, March 27, 2001 6:14 PM
Subject: Re: Which is number 1 cylinder?


> I had two 1600 Roadsters for a while and the distributors were exactly
> 180 degrees off from one another.  This is due to the distributor
> having an off-center shaft slot and the oil pump shaft thingie having a
> centered shaft slot.  The oil pump shaft thingie (sorry about this
> technical talk) can fit in two ways, but the distributor will fit in
> only one.  I asked and was told "it doesn't really matter".  Please
> correct me if I'm wrong about it not mattering...
>
> Adam
> '70 1600
>
> --- "WILSON,BOB (A-SantaClara,ex1)" <bob_wilson@agilent.com> wrote:
> > Hi list,
> >
> > This is an embarassing question but I must ask. Which is number 1
> > cylinder
> > and what is the pattern of the distributor wires?
> >
> > I thought it was this way, but when I tried to start my newly rebuilt
> > engine
> > yesterday, it wouldn't run until I reversed the spark plug wires. I
> > am
> > confused (again).
> >
> > This is what I thought was right:
> >
> > Block:
> >  ----------------------
> >  |                    |
> >  |  4    3    2    1  |   Radiator is here.
> >  |                    |
> >  ----------------------
> >
> > Distributor:
> >
> >        1  2
> >        3  4
> >
> >
> > The above is how it looks when looking down from above the car. Left
> > is the
> > rear of the car (or firewall) and to the right is the front of the
> > car (or
> > radiator). So this view would be if you were on the passenger side of
> > the
> > car looking down on the engine compartment.
> >
> > The above does not work. I had to reverse the block spark plug
> > numbers so
> > that 1 was to the rear and 4 was to the front, to get the engine to
> > run.
> >
> > What is going on? I seem to remember that the piston rods were
> > numbered as I
> > have shown above.
> >
> >
> > Any suggestions?
> >
> > Bob Wilson
> > 1970 1600 stroker.
> Get email at your own domain with Yahoo! Mail.
> http://personal.mail.yahoo.com/?.refer=text

<Prev in Thread] Current Thread [Next in Thread>