fot
[Top] [All Lists]

RE: Power for a lift.

To: "'Bob Kramer'" <rgk@flash.net>, "Russ Moore" <rem@cbord.com>
Subject: RE: Power for a lift.
From: "Russ Moore" <rem@cbord.com>
Date: Thu, 7 Nov 2002 16:18:11 -0500
Should be easily able to, especially if they have access to used motors and
contactors. 

Having no lift vs. having a lift is the same difference as working out in a
snowbank in the dark,in a blizzard, with no light, coat or proper tools is
to working in a dry, warm, well lit shop with stereo all the right tools and
someone to bring you a Guinness at the appropriate time! I have tried both
modes, not a hard choice, believe me!

Problem is, once you're had one, you can't go back to working without one.

I'm spoiled!

Russ


-----Original Message-----
From: Bob Kramer [mailto:rgk@flash.net]
Sent: Thursday, November 07, 2002 4:15 PM
To: Russ Moore
Cc: fot@autox.team.net
Subject: Re: Power for a lift.


Russ,
I'm on it. I took the motor and controller off the post last night and
dropped it off at a large motor rebuilder this morning for that very
purpose. I'm hoping they can swap it  out and set it up so I can just hook
up the leads at a price less than a converter. We'll see.
Bob
----- Original Message -----
From: "Russ Moore" <rem@CBORD.com>
To: "'Bob Kramer'" <rgk@flash.net>; "Russ Moore" <rem@CBORD.com>
Cc: <fot@autox.team.net>
Sent: Thursday, November 07, 2002 11:50 AM
Subject: Power for a lift.


> Bob,
> I have seen those before, they work pretty well. What are the economics of
> finding a 220volt 4-5 hp motor and using it to power the device. I think
> they're quite a bit (lots) less expensive than the converter. Even if you
> had to alter a mounting plate it would be worth it. Typically a 5-6 HP
> compresser would have just the item I believe. Getting it to work and mate
> with the gear reduction shouldn't be too difficult.
> There are actually some places that specialize in "used" electrical
> equipment. Even a new motor is likely just a couple of hundred dollars
from
> a place like Grainger. There are better deals than theirs out there.......
> Not a bad price.
>
> Russ Moore
>
>
> -----Original Message-----
> From: Bob Kramer [mailto:rgk@flash.net]
> Sent: Thursday, November 07, 2002 12:13 PM
> To: Russ Moore
> Cc: fot@autox.team.net
> Subject: Re: TR4A bonnet hinges
>
>
> Russ,
> It's  a Werther assymetrical 2 post screw type lift, actually 2 of them.
> Electrical/Mechanical. They are screw driven off one 4 HP 3 phase motor.
The
> motor sits on top of one post and runs that screw. A driveshaft
arrangement
> though a raised floor panel runs the other side. The Phase converter
> manufacturers say it will take a 7.5 HP rotory converter ($600) to run it,
> but Werther says other people have tried it and it doesn't work. I can't
see
> why it wouldn't work, but I don't want to go out and throuw good money
after
> bad. The lifts were cheap ($850), so the total price is very attractive
> compared to a new lift of the same capacity and features.
>
> Bob
>
> ----- Original Message -----
> From: "Russ Moore" <rem@CBORD.com>
> To: "'Bob Kramer'" <rgk@flash.net>
> Sent: Thursday, November 07, 2002 10:25 AM
> Subject: RE: TR4A bonnet hinges
>
>
> > Bob,
> > If the lift is the old "in-ground" hydraulic type, run like hell.

<Prev in Thread] Current Thread [Next in Thread>