healeys
[Top] [All Lists]

Re: [Healeys] "Before the Shrouds"

To: "Mark LaPierre" <lapierrem@sbcglobal.net>, <healeys@Autox.Team.Net>
Subject: Re: [Healeys] "Before the Shrouds"
From: "Rich C" <richchrysler@quickclic.net>
Date: Sun, 22 Mar 2009 11:26:39 -0400
Mark, et al,

Items suggested to install before the front shroud, following Mark's list: I 
always install all suspension and steering components front and back so the 
car is able to be rolled around the shop a.s.a.p.

1. trafficator isn't affected by shroud installation. I'd suggest that 
certainly the grille assembly is the one that gets in the way of that.

1.5 ditto for front end toe in. Agree the car should be road weight before 
toe in adjustment.

2. black felt paper insulations inside bulkhead area

3. On the Hundred, the air duct can be installed later; your choice. That 
way it's out of the way of accessing the right front fender bolts. On the 6 
cylinder model I preinstall the air ducts before front shroud, but the 
blower motor will have to hang loose to access fender bolts, BUT do have the 
ducts securely clamped to the blower apertures. After a trial fit, the 
blower can be relocated into it's bolts and washers later.

4. all wiring possible, including dip switch harness routing

5. all hydraulic lines and clips

6. radiator not necessary, your choice

7. bleeding of all hydraulics (mostly in case you have a problematic leaky 
fitting to access)

8. Engine, gearbox install your choice. Can certainly do later, but a little 
easier for clearances with shroud off.

9. heater and demister vents under dash cowl area

10. wiper motor, wiring and rack should be prefitted and ready to fit wheel 
boxes through shroud when installed later

11. bulkhead and left foot box insulation panels (must be installed before 
engine goes in)

12. oil line from engine bay through firewall to gauge location

13. steering column and associated blanking plates and grommets; can do 
later, it's just much easier to stand above work area with easy access.

There is no hard and fast step by step sequence, but these items are at 
least worth consideration.

Rich Chrysler


----- Original Message ----- 
From: "Mark LaPierre" <lapierrem@sbcglobal.net>
To: <healeys@Autox.Team.Net>
Sent: Sunday, March 22, 2009 7:49 AM
Subject: [Healeys] "Before the Shrouds"


> Since I'm at the panel reinstall stage, I thought I would initiate a list 
> of
> things to
> complete before the installation of shrouds and other body panels to help
> others
> plan out their schedule when the time comes.  Some operations are a bear
> after
> the panels are installed.
>
> Please add to or delete what ever is on the list if you think it  may help
> other enthusiasts later
> on.
>
> 1.   Trafficator install and adjust.  ( real pain in the behind)
>
> 1.5  Front end alignment
>
> 2.   Heater and fresh air ducting install
>
> 3.   Much of the electrical wiring harness
>
> 4.    Hydraulic plumbing up to the fluid canister and Master cylinders
>
> 5.    Radiator install and plumbing
>
> 6.    Bleeding the brakes and other misc.  brake work
>
> 7.     Engine/ Trany install
>
> 8.     Most of the front end suspension work
_______________________________________________
Support Team.Net http://www.team.net/donate.html

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys


http://www.team.net/archive

<Prev in Thread] Current Thread [Next in Thread>