healeys
[Top] [All Lists]

Re: [Healeys] spray varnishes for BJ8 dash

To: "Oudesluys" <coudesluijs@chello.nl>
Subject: Re: [Healeys] spray varnishes for BJ8 dash
From: "R. Price Lindsay" <price@advocateadvisors.com>
Date: Sat, 9 Jan 2010 16:45:32 -0600
I am refinishing my dash and recovering the dash top. The dash is out  
of the car but I can't get the top to break free. It seems to be held  
around the defrost vents but I can't see how or where. Is there a bolt  
or screw above the heater that I can't see?  Do the rubber elbows need  
to be removed - if so, how do I do that?

Thank you.

Price Lindsay

67 BJ8

On Jan 2, 2010, at 5:01 AM, "Oudesluys" <coudesluijs@chello.nl> wrote:

> Depends on the finish you want. In all cases prepare the wood/veneer  
> as best as you can using 320 sandpaper.
> If you want a high gloss finish you need a lot of coats and sanding  
> in between to fill up the woodgrain. However this may crack and  
> separate in time. The best way to go, I found, is using thinned PU  
> boat varnish applied by a soft brush, at least 5 thin coats with  
> light sanding in between the coats. Spraying would give a similar  
> result. The first coat needs to be sanded with 320 grade when the  
> varnish is stil wet to fill the grain. Very messy. After all grains  
> are filled up leave the coat dry thoroughly for at least two weeks  
> and sand the final coat using 2000 flower paper on a flat board,  
> check if all grains are filled and polish with a good wax polish or  
> even brass polish and finish with carnabu wax. I did several TR  
> dashboards that way.
> If you want a satin finish polishing with a minimum of 10 layers of  
> raw linseed oil may be the best. Apply with a lintfree cloth in very  
> thin layers and rub in. Leave to dry for a week between the coats.  
> Buff up the final coat. It is a resilient and higly water and heat  
> resistant coating but you have to maintain the dashboard by rubbing  
> on some lindseed oil each year to keep it really nice. Easy enough.
> It is best to keep a varnish coat on wood as thin as possible to  
> avoid cracking and separation.
> Pouring on the product may lead to a very glossy and even finish but  
> I fear it will not last long if exposed to sun, varying temperatures  
> and humidities, the same goes for any thickly applied product.
> Do not expect to much from the UV protection from any product.  
> AFAIAC there is not much between them.
> Kees Oudesluijs
> NL
>
>
> Richard Kahn schreef:
>> Has anyone been successful using spray on finishes on the wood  
>> dash? Helmsman
>> rattle can has UV protection.  Any other brands suggested? How many  
>> coats
>> should I expect? I liked the Enviro-Tex pour on idea but it does  
>> not have UV
>> protection and goes on thick which may not hold up in the heat of  
>> the sun
>> (expansion and contraction which caused separation and cracking).
>> Rich Kahn
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
>
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> You are subscribed as price@advocateadvisors.com
>
> http://www.team.net/archive
_______________________________________________
Support Team.Net http://www.team.net/donate.html

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys


http://www.team.net/archive

<Prev in Thread] Current Thread [Next in Thread>