Sounds good to me! A fine idea.
On Jan 11, 2015, at 6:46 PM, Phil Jarrett wrote:
> We need to update the nasty boy name.... It is way out of date. I enjoy every
> Healey out there and every time I here it's a nasty boy my hair lifts off my
> neck. Modified would be a much softer designation for all...
> Standing by for the flack
> Cheers Phil
>
>
> Sent from my iPhone
>
>> On Jan 11, 2015, at 20:49, Wilko2 <e-wilkins@cox.net> wrote:
>>
>> Sounds like a fun prject. The only thing that comes to mins that you'll need
>> the O2 sensors so you ECM can regulate the mixture.
>>
>> "Nasty Boy" is what you'll have.
>>
>>
>>
>>> On Jan 11, 2015, at 4:42 PM, Chris Scholz wrote:
>>>
>>> Here is an update on my 100-6. It was first going to be a refresh of the
>>> iron 6. Then it was decided to paint the engine bay while the engine and
>>> tranny were out. Then the fenders were removed. Then the doors, trunk,
>>> hood. Then the seats, carpet and dash. Then the wiring and brake lines. And
>>> then the bonnet (front and rear ) was removed. Finally, all the suspension
>>> and axles and gas tank are gone. We initially thought only the fenders and
>>> bottom of the doors had rust. After blasting with crushed glass and baking
>>> soda we found pinholes in the sills, the trunk floor pan, and the frame
>>> where the door hinges bolt to the frame. There were dents all through the
>>> aluminum shroud which had been filled with bondo. The good news is the
>>> frame is in perfect shape, including the outriggers.
>>> My mechanic purchased my radiator, tranny and engine for $5k and I bought a
>>> used LS1 all aluminum V8 from a 2000 Z28 that is being refreshed this week.
>>> Front disc brakes from Denis Welch. Updating the rear with 3.54 gear and
>>> Quaife limited slip from a fellow Healey subscriber. Will probably buy an
>>> aluminum radiator from Wizard cooling with a 14" electric fan. Will have to
>>> figure out how much to trim the foot boxes to fit the bell housing.
>>> Hopefully no more than 1.5-2". Will be running exhaust on both sides of the
>>> car. Will then modify the LS1 computer to remove the O2 sensor from the
>>> cats and to run the new corvette fuel pump and control the electric fan.
>>> Will keep everyone updated through the fabrication. Thanks for the advice.
>>>
>>> <photo.JPG>
>>>
>>> <image.jpeg>
>>>
>>> Sent from my iPhone
>>> Chris Scholz OD_______________________________________________
>>> Support Team.Net http://www.team.net/donate.html
>>> Suggested annual donation $12.75
>>> Archive: http://www.team.net/archive
>>> Forums: http://www.team.net/forums
>>>
>>> Healeys@autox.team.net
>>> http://autox.team.net/mailman/listinfo/healeys
>>>
>>> Unsubscribe/Manage:
>>> http://autox.team.net/mailman/options/healeys/e-wilkins@cox.net
>>
>> _______________________________________________
>> Support Team.Net http://www.team.net/donate.html
>> Suggested annual donation $12.75
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>>
>> Healeys@autox.team.net
>> http://autox.team.net/mailman/listinfo/healeys
>>
>> Unsubscribe/Manage:
>> http://autox.team.net/mailman/options/healeys/pjarrett14@gmail.com
>>
_______________________________________________
Archive: http://www.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
|