mgs
[Top] [All Lists]

Re: [Mgs] Advice wanted on MGB Brake Master Cylinder

To: "Dodd, Kelvin" <doddk@mossmotors.com>, The Roxter
Subject: Re: [Mgs] Advice wanted on MGB Brake Master Cylinder
From: Rick Lindsay <rolindsay@yahoo.com>
Date: Wed, 22 Aug 2007 14:18:06 -0700 (PDT)
Dudes, please keep me plugged in on this topic.  I am
planning to rebuild my master cylinder and it is of
the same type described by The Roxter.  I've rebuilt a
few MCs before (Jaguars) but never an MGB.  As we
attack these beasts lets make sure to photograph and
document the procedure.  Kelvin makes a good point. 
If its a hard job then there's all the more reason to
document it.

best,

rick
'70 MGB split-bumper Tourer
Italian iron too 
--- "Dodd, Kelvin" <doddk@mossmotors.com> wrote:

> Roxter:
> 
> I hate to say this, but of all the bits on a 70-76
> MGB I draw the line
> at rebuilding the master cylinder.
> 
> I've never had very good luck getting the delrin
> spacer out, then you
> have the dreaded clip to negotiate.
> 
> While new ones are still available, I just bite the
> bullet and install a
> new one.
> 
> 
> 
> 
> Kelvin Dodd
> 
> 
> > -----Original Message-----
> > From:
> mgs-bounces+doddk=mossmotors.com@autox.team.net
> [mailto:mgs-
> > bounces+doddk=mossmotors.com@autox.team.net] On
> Behalf Of The Roxter
> > Sent: Wednesday, August 22, 2007 1:51 PM
> > To: mgs@autox.team.net
> > Subject: [Mgs] Advice wanted on MGB Brake Master
> Cylinder
> >
> > My Victor uses an MGB Brake Master Cylinder, the
> kind with the big
> > cylindrical reservoir that leans forward, with the
> big round cap.
> >
> > I sent it off to be reconditioned around four
> months ago, but it was
> > returned finally last week with no work done. I'm
> pretty sure they
> > didn't know how to get it apart.
> >
> > I'm trying to do it myself now, but have run into
> a snag.
> >
> > I got the spring clip off the actuator rod, then
> got the inner spring
> > clip off easily.
> >
> > The washer that the inner spring clip goes on top
> of is stuck in the
> > bore. The actuator rod is moving easily, so I have
> tried to use its
> > spring pressure to move the washer out, by pushing
> the rod all the way
> > in and then releasing it so it hits the washer. I
> also tried banging
> the
> > open end of the cylinder on a hardwood board,
> which compresses the
> > spring on the actuator rod, hoping the weight of
> the assembly would
> move
> > the washer out the bore, but it has not budged. I
> also tried tapping
> > around the washer, hoping this might loosen its
> grip on the bore, but
> > this didn't help either.
> >
> > I'm heading for the parts store to get a spray can
> of Liquid Wrench,
> > hoping that soaking the area of the washer
> overnight might help to
> > loosen it.
> >
> > The washer is stuck where it started, right below
> the groove where the
> > inner spring washer rests.
> >
> > Any suggestions or magic tricks, guys?
> >
> > -The Roxter
_______________________________________________

Edit your replies

Mgs@autox.team.net
http://autox.team.net/mailman/listinfo/mgs

<Prev in Thread] Current Thread [Next in Thread>