triumphs
[Top] [All Lists]

Re: [TR] Alloy valve cover oil consumption

To: Tony Drews <tony@tonydrews.com>
Subject: Re: [TR] Alloy valve cover oil consumption
From: Brad Kahler <bkahler1@gmail.com>
Date: Sat, 23 Aug 2014 12:20:22 -0400
Cc: Triumphs <Triumphs@autox.team.net>
Delivered-to: mharc@autox.team.net
Delivered-to: triumphs@autox.team.net
References: <CADm3DLFDAW7k1K0cp8E-=mK13DCnXUuss7ztinxKweA04JLFdQ@mail.gmail.com> <20140822175332.9D3B025857E8@autox.team.net>
Tony & All,

Working from a tip from Irv I went out and bought a PCV valve that I was
able to add into the line from the valve cover to the carburetor flame
arrestor.  My TR4 has the mid production emissions setup and my first test
drive with the PCV valve installed was good.  What I found interesting was
my idle RPM dropped from 800 to 600 once I installed the PCV valve.

I'd rather not install a catch tank as I would think if everything is
working right the oil should now stay in the valve cover instead of getting
sucked into the carburetors.  Weather permitting I'm going to take a drive
this afternoon and then see what things look like.

Thanks for all the tips and suggestions!

Brad





On Fri, Aug 22, 2014 at 1:53 PM, Tony Drews <tony@tonydrews.com> wrote:

> I can't comment on which solution is the best from any personal
> experience, but I'd be inclined to epoxy something to the inside of the
> cover instead of riveting it mainly for cosmetic reasons (no holes to drill
> in the cover).  I'd think about likely paths for oil to be slung and look
> to block those with the baffle.
>
> Tony Drews
>
> At 08:46 AM 8/22/2014, Brad Kahler wrote:
>
>> When I bought my TR4 back in 2010 it came with a TriuimphTune alloy valve
>> cover.  While nice looking, the fact that it has no baffle or screen over
>> the breather tube going to the carburetors causes oil consumption to
>> increase.  I've been doing some google searching and have come up with
>> several possible solutions on how to create a baffle.
>>
>> One involves epoxying an aluminum baffle over the opening, another uses
>> some wire and a small aluminum plate held in place over the hole.  Still
>> another was adding a small baffle over the opening by riveting it in place
>> with solid aluminum rivets.  And finally someone apparently has wrapped a
>> screen over the discharge end of the tube and and then pushed the hose
>> over
>> it.
>>
>> I'm sort of partial to the aluminum plate and rivet idea although I'm not
>> keen on drilling holes in the valve cover.  However I might try the screen
>> method since it would be a quick and dirty test.
>>
>> Has anyone tried a different solution to what I've listed?  If so I'd love
>> to hear about it.
>>
>> Thanks,
>>
>> Brad
>>
>> ** triumphs@autox.team.net **
>>
>> Donate: http://www.team.net/donate.html
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Unsubscribe/Manage: http://autox.team.net/mailman/options/triumphs/tony@
>> tonydrews.com
>>
>
> ** triumphs@autox.team.net **
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage: http://autox.team.net/mailman/
> options/triumphs/bkahler1@gmail.com

** triumphs@autox.team.net **

Archive: http://www.team.net/archive

<Prev in Thread] Current Thread [Next in Thread>