triumphs
[Top] [All Lists]

Re: [TR] TR6 no start

To: fishplate@gmail.com, triumphs@autox.team.net s=20150623; t=1436718580; bh=L2cQXmjpelwNeEuYT4oVbOSIR31GkwUsAQnG23USnIc=; h=From:To:Subject:Message-ID:Date:MIME-Version:Content-Type; b=ts93wLq6nRAgmu5IthpgvJG2LBUhGMc3sDW1qhD57Dqkw3zL0H5cXlvsm+y1VyQuE DmEi+SKsF+O1KGZQa/Hi1NG4D5dC3zv0g96nX7azUaT5agVNBjDdc0BhTr6vDQ+eOn ZDptluq7bAgG4RDq7aVTsHXU2xO5GiW8nRW93cPw=
Subject: Re: [TR] TR6 no start
From: Chip19474@aol.com
Date: Sun, 12 Jul 2015 12:29:35 -0400
Delivered-to: mharc@autox.team.net
Delivered-to: triumphs@autox.team.net
Full-name: Chip19474
--===============1756326579861035765==

--part1_b4dc9.4d5bf2fa.42d3efee_boundary
Content-Transfer-Encoding: 7bit

Jeff,
 
It almost sounds like the bowl floats are set incorrectly or the float  
valves are sticking....net result is too much fuel in the bowls which dumps 
into  the engine....mixture gets too rich, motor dies with a puff of black  
smoke.
 
One quick way to check this without removing the bowls is to take one or  
two spark plugs out after you've tried to start it and see if the plugs are 
wet  (fouled) with fuel.  If they are, try tapping on the sides of both float 
 bowls with the wooden part of a hammer.....if some dirt got past the fuel 
filter  and is stuck in the float valve, you may be able to dislodge it. 
 
If the problem doesn't point to stuck float valves or incorrectly set  
floats, it may be time to check cylinder compression.  If compression  isn't 
reasonably consistent across all cylinders, take the valve cover off;  have 
someone crank the engine while you watch the operation of each rocker  
arm....I've seen bent pushrods and I've seen the rocker arm adjuster nuts  back 
off 
completely and leave the pushrod just flopping around.....stuff  happens!
 
Good luck
 
Chip Krout
Delaware Valley Triumphs,  Ltd.
Delaware Valley Miata Club
Skippack, PA 
 
 
In a message dated 7/11/2015 8:31:29 P.M. Eastern Daylight Time,  
fishplate@gmail.com writes:

Interestingly, when I replaced the carb, it tried to start with  an
empty bowl.  But as it filled, it got more reluctant to  start.  Spins
like crazy, but no  pop.


--part1_b4dc9.4d5bf2fa.42d3efee_boundary
Content-Transfer-Encoding: quoted-printable

<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META content=3D"text/html; charset=3DUS-ASCII" http-equiv=3DContent-Type>
<META name=3DGENERATOR content=3D"MSHTML 11.00.9600.16476"></HEAD>
<BODY id=3Drole_body style=3D"FONT-SIZE: 10pt; FONT-FAMILY: Arial; COLOR:=
 #000000"=20
bottomMargin=3D7 leftMargin=3D7 rightMargin=3D7 topMargin=3D7><FONT id=3Dr=
ole_document=20
color=3D#000000 size=3D2 face=3DArial>
<DIV>Jeff,</DIV>
<DIV>&nbsp;</DIV>
<DIV>It almost sounds like the bowl floats are set incorrectly or the floa=
t=20
valves are sticking....net result is too much fuel in the bowls which dump=
s into=20
the engine....mixture gets too rich, motor dies with a puff of black=20
smoke.</DIV>
<DIV>&nbsp;</DIV>
<DIV>One quick way to check this without removing the bowls is to take one=
 or=20
two spark plugs out after you've tried to start it and see if the plugs ar=
e wet=20
(fouled) with fuel.&nbsp; If they are, try tapping on the sides of both fl=
oat=20
bowls with the wooden part of a hammer.....if some dirt got past the fuel=
 filter=20
and is stuck in the float valve, you may be able to dislodge it.&nbsp;</DI=
V>
<DIV>&nbsp;</DIV>
<DIV>If the problem doesn't point to stuck float valves or incorrectly set=
=20
floats, it may be time to check cylinder compression.&nbsp; If&nbsp;compre=
ssion=20
isn't reasonably consistent across all cylinders,&nbsp;take the valve cove=
r off;=20
have someone crank the engine while you watch the operation of each rocker=
=20
arm....I've seen bent pushrods&nbsp;and I've seen the rocker arm adjuster=
 nuts=20
back off completely and leave the pushrod just flopping around.....stuff=
=20
happens!</DIV>
<DIV>&nbsp;</DIV>
<DIV>Good luck</DIV>
<DIV>&nbsp;</DIV>
<DIV><FONT face=3D"Arial Baltic">Chip Krout<BR>Delaware Valley Triumphs,=
=20
Ltd.<BR>Delaware Valley Miata Club<BR>Skippack, PA </FONT></DIV>
<DIV>&nbsp;</DIV>
<DIV>
<DIV>In a message dated 7/11/2015 8:31:29 P.M. Eastern Daylight Time,=20
fishplate@gmail.com writes:</DIV>
<BLOCKQUOTE=20
style=3D"PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: blue 2px solid"=
><FONT=20
  style=3D"BACKGROUND-COLOR: transparent" color=3D#000000 size=3D2=20
  face=3DArial>Interestingly, when I replaced the carb, it tried to start=
 with=20
  an<BR>empty bowl.&nbsp; But as it filled, it got more reluctant to=20
  start.&nbsp; Spins<BR>like crazy, but no=20
pop.<BR></FONT></BLOCKQUOTE></DIV></FONT></BODY></HTML>
--part1_b4dc9.4d5bf2fa.42d3efee_boundary--

--===============1756326579861035765==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline


** triumphs@autox.team.net **

Archive: http://www.team.net/archive

--===============1756326579861035765==--

<Prev in Thread] Current Thread [Next in Thread>