Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Fot\]\s+setting\s+sleeves\/barrels\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Fot\]\s+setting\s+sleeves\/barrels\s*$/: 6 ]

Total 6 documents matching your query.

1. [Fot] setting sleeves/barrels (score: 1): Author: Tony Drews <tony@tonydrews.com>; Date: Tue, 19 May 2009 20:18:01 -0500; Several list members had inquired about these sets. They are now -- Ted Schumacher tedtsimx@bright.net http://www.tsimportedautomotive.com 108 S. Jefferson St. Pandora, Ohio, USA 45877 Fax: 419.384.3; /html/fot/2009-05/msg00195.html (10,770 bytes)
2. Re: [Fot] setting sleeves/barrels (score: 1): Author: "David Talbott" <dtalbott@archrepro.com>; Date: Tue, 19 May 2009 18:56:07 -0700; One thing I did when putting in new sleeves last summer was to get a 12 inch extension bit for a 1/4 inch drill and mount a wire brush on the end to get down to the sleeve seat and wire brush it to g; /html/fot/2009-05/msg00197.html (9,085 bytes)
3. Re: [Fot] setting sleeves/barrels (score: 1): Author: "Mark Pendergrass" <mpendy@dishmail.net>; Date: Wed, 20 May 2009 07:12:51 -0700; _______________________________________________ Support Team.Net http://www.team.net/donate.html http://www.fot-racing.com Fot mailing list Fot@autox.team.net http://autox.team.net/mailman/listinfo/f; /html/fot/2009-05/msg00198.html (7,165 bytes)
4. Re: [Fot] setting sleeves/barrels (score: 1): Author: Ted Schumacher <tedtsimx@bright.net>; Date: Wed, 20 May 2009 10:15:20 -0400; I ruined a 205-60-15 Hoosier Speedster last weekend. The other three are about half worn. I went fishing (without bait) earlier this week to the list hunting for a good used tire to replace the trash; /html/fot/2009-05/msg00199.html (6,777 bytes)
5. Re: [Fot] setting sleeves/barrels (score: 1): Author: Bill Babcock <billb@bnj.com>; Date: Wed, 20 May 2009 09:38:17 -0700; I make a loop in the wire to keep from making that sharp bend.B The length has to be long enough that the solder does not penetrate the length of the stranded wire - if it does then you just added m; /html/fot/2009-05/msg00206.html (9,454 bytes)
6. Re: [Fot] setting sleeves/barrels (score: 1): Author: "Kramer, Robert" <RKramer@rdoequipment.com>; Date: Wed, 20 May 2009 11:54:43 -0500; That's the guy. Bob, I suspect your starter would be fine for another nine years if you did this little fix. _______________________________________________ Support Team.Net http://www.team.net/donat; /html/fot/2009-05/msg00208.html (10,991 bytes)

Current List: 1 - 6
Page: [1]