Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[oletrucks\]\s+going\s+Saturday\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[oletrucks\]\s+going\s+Saturday\s*$/: 8 ]

Total 8 documents matching your query.

1. [oletrucks] going Saturday (score: 1): Author: "Tom C." <c_tom@bellsouth.net>; Date: Thu, 6 Nov 2003 19:05:11 -0500; Well I found a junk yard about 60 miles from me that says they should have a 1970-1981 Camaro rear end for my 55 2nd. They want $150.00 and they will take it out. If they by chance have one out alrea; /html/oletrucks/2003-11/msg00108.html (7,442 bytes)
2. RE: [oletrucks] going Saturday (score: 1): Author: "Joseph Garcia" <joe_garcia@earthlink.net>; Date: Thu, 6 Nov 2003 18:12:37 -0800; I have a rear end out of a 1979 Camaro in the backyard that I can take a Digital Picture of it tomorrow morning and email it to you. Want any measurements ? Joe have a want oletrucks is devoted to C; /html/oletrucks/2003-11/msg00112.html (8,103 bytes)
3. Re: [oletrucks] going Saturday (score: 1): Author: "K. M. Lehmann" <klehmann@bentonrea.com>; Date: Fri, 7 Nov 2003 07:32:17 -0800; Tom the rear your looking for can be recognized with the wide leaf springs and one shock mount going forward and one aft, most good ones had a larger pinion shaft and yoke than the standard Chev 10 b; /html/oletrucks/2003-11/msg00116.html (8,358 bytes)
4. Re: [oletrucks] going Saturday (score: 1): Author: Wayne Osborne <wayne@chevytrucks.org>; Date: Fri, 07 Nov 2003 11:00:43 -0800; Also main thing is made sure it is the correct width. You'll have to move the leaf spring pads on the rear ends housing and reweld in correct position,as they are not the correct width to mate to you; /html/oletrucks/2003-11/msg00117.html (10,028 bytes)
5. Re: [oletrucks] going Saturday (score: 1): Author: "K Ohlgren" <kjohlgren@hotmail.com>; Date: Fri, 07 Nov 2003 17:04:44 +0000; I picked up an '86 Trans Am (camaro) rear end for $200 that is under my 58. it 62" wide, disk brakes and Posi-Trac. I had to cut all of the coil spring stuff off and weld on spring pads. I flipped t; /html/oletrucks/2003-11/msg00119.html (11,652 bytes)
6. Re: [oletrucks] going Saturday (score: 1): Author: zman <zman@gibbon.kungfumonkey.com>; Date: Fri, 7 Nov 2003 12:16:08 -0500 (EST); Pretty good memory, I'm putting a Camaro rear under my '59. Those are the measurements I remember as well. I'm doing it mainly for the gearing. -- Scott H. Zekanis zman@kungfumonkey.com http://www.ro; /html/oletrucks/2003-11/msg00120.html (9,909 bytes)
7. Re: [oletrucks] going Saturday (score: 1): Author: "K. M. Lehmann" <klehmann@bentonrea.com>; Date: Fri, 7 Nov 2003 09:37:27 -0800; Good info Wayne I'm sure your measurements are correct. My unit, '79 Camaro , roughly measures 61", I have 8" wheels with 3.5" backset and still have a couple inches between the bed and 9.50 x 15 tir; /html/oletrucks/2003-11/msg00121.html (11,262 bytes)
8. RE: [oletrucks] going Saturday (score: 1): Author: "Tom C." <c_tom@bellsouth.net>; Date: Fri, 7 Nov 2003 23:45:35 -0500; Thanks Wayne for all the info. According to a few others you were right on with your measurments from memory. I went out and remeasured my original and it is around 62" from outside to outside of the; /html/oletrucks/2003-11/msg00128.html (10,781 bytes)

Current List: 1 - 8
Page: [1]