Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Engine\s+Bearing\s+Replacement\?\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Engine\s+Bearing\s+Replacement\?\s*$/: 7 ]

Total 7 documents matching your query.

1. Engine Bearing Replacement? (score: 1): Author: "Scott Gardner" <gardner@lwcomm.com>; Date: Sat, 30 Aug 1997 14:52:56 +0000; Warren, I think it would be a good idea to replace the bearings as you described. Not all parts of the engine wear out at the same rate, and I've heard 30-40,000 miles as a fair service interval for; /html/mgs/1997-08/msg02130.html (7,826 bytes)
2. Re: Engine Bearing Replacement? (score: 1): Author: Arthur Pfenninger <ch155@FreeNet.Buffalo.EDU>; Date: Sat, 30 Aug 1997 17:27:20 -0400 (EDT); It may as simple as your oil pressure relief valve being bad. It's a cheap fix. Per my previous post you can't replace the main bearings without pulling the engine. You need to remove the crank shaft; /html/mgs/1997-08/msg02136.html (8,486 bytes)
3. Re: Engine Bearing Replacement? (score: 1): Author: barneymg@juno.com (Barney Gaylord); Date: Sat, 30 Aug 1997 23:54:21 EDT; pulling the engine. You need to remove the crank shaft to get the top of the bearings out, not to mention how hard it would be to try and pull the caps off while laying on your back. Uh, pardon me? Y; /html/mgs/1997-08/msg02155.html (8,022 bytes)
4. Re: Engine Bearing Replacement? (score: 1): Author: mgbob@juno.com (ROBERT G. HOWARD); Date: Sun, 31 Aug 1997 07:30:49 EDT; I've seen a mechanic use a tool to change the upper half of main bearings with the engine in the car. The thing is shaped like a bearing shell, sort of, with a pin on it that engages the oil supply h; /html/mgs/1997-08/msg02165.html (9,335 bytes)
5. Re: Engine Bearing Replacement? (score: 1): Author: Arthur Pfenninger <ch155@FreeNet.Buffalo.EDU>; Date: Sun, 31 Aug 1997 08:00:45 -0400 (EDT); Let me know how it turns out if decide to do it. I found an article yesterday that confirms it can be done. I'm wrong! ...Art; /html/mgs/1997-08/msg02168.html (9,983 bytes)
6. Re: Engine Bearing Replacement? (score: 1): Author: RJohn50603@aol.com; Date: Sun, 31 Aug 1997 10:17:50 -0400 (EDT); << > I am having problems with low oil pressure on my 70 Roadster and a Make sure you get the proper size bearings. If your want to do the mains too, they can "rolled" into place without removing the; /html/mgs/1997-08/msg02170.html (7,558 bytes)
7. Re: Engine Bearing Replacement? (score: 1): Author: Chad Cooper <mgb72@airmail.net>; Date: Sun, 31 Aug 1997 10:21:12 -0500; Arthur Pfenninger wrote:Warren, I replaced those bearings without pulling the engine, just takes patience. The motor mounts have to be loosened so you can get the pan off, other than that it was no b; /html/mgs/1997-08/msg02173.html (7,455 bytes)

Current List: 1 - 7
Page: [1]